LG
Model: M2762DL PC
Chassis / Version: LD93A
Panel: M270H1-L01 Rev. C1
Inverter (backlight): integrated into PSU
PWM Inverter: OZ9938GN
Trans Inverter: TMS94493CT
Power Supply (PSU): PLLM-M901D P / N: 3PAGC20002A-R Rev.1.0
PWM Power: STR-W6253
MainBoard: EAX62848101 (1) M20 / 22/23 / 2762D-PZL
IC MainBoard: LMD9201A-LF-SD, AP1W084D, 1006B, K4T51163QG-HCF7, 24C512, 24C08W, MX25L12845EM, LGE40RC-LF, WJCE6355, MAX232, LVC541A, TAS5709, 24C02B, APW70 AZ, AZW70 AZD8070
Control: KB33871424
Appearance
LG M2762DL
General recommendations for repairing TV LCD
If the TV does not turn on, the indicators on its front panel do not light up and do not blink, just as if the TV does not respond to the remote control and buttons, does not emit any sounds or any signs of operability when connected to the network, there is a certain probability of a PLLM-M901D power supply module and he needs repairs. Sometimes with similar manifestations a problem can only occur in the absence of standby power. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is broken in the power supply, in most cases a breakdown of the power switch in the STR-W6253 is detected, which is integrated with the PWM controller. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor elements or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip STR-W6253 or broken resistors in its bundle.
PLLM-M901D includes a power converter for display backlight lamps - an inverter.
Sometimes the LG M2762DL TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the inverter, or of the lamps themselves, which can be checked by replacement. In such cases, it is necessary to verify the serviceability of all electrolytic capacitors of the filter by the inverter power. When disabling the inverter protection (to enable diagnostics), special care must be taken in view of the risk of failure of the power elements. After completing all repair work, it is imperative to restore the protection circuits for full and safe further operation of the TV by the user.
Diagnosis and repair of the EAX62848101 motherboard usually begins with a test of the performance of the stabilizers and power converters of the module chips. In some cases, a software update is required. Board repair and chip replacement LMD9201A-LF-SD, AP1W084D, 1006B, K4T51163QG-HCF7, 24C512, 24C08W, MX25L12845EM, LGE40RC-LF, WJCE6355, MAX232, LVC541A, TAS5709, 24C0210 AZG, AZD, AVI, WZGZZZZ, AVZ, AVZ, AVI, AVZ equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can sometimes be localized by the heating method.
Once again, remind users! Attempts to self-repair the LG M2762DL TV without the appropriate qualifications and experience can lead to its complete non-repairability!
Service manual / schematic diagram -------------> LG M2762DL Chassis LD93A
CHASSIS : LD93A; MODEL : M2762D, M2762D-P(W)ZL
The appearance of the MainBoard EAX62848101 is shown in the figure below:
EAX62848101
The appearance of the power supply
Main features of the device LG M2762DL:
Installed matrix (LCD panel) M270H1-L01 Rev. C1.
To power the backlight, a converter is used, combined with a power supply, controlled by the OZ9938GN PWM controller. The transformer TMS94493CT is installed in the inverter converter.
The necessary supply voltages for all nodes of the LG M2762DL TV are generated by the PLLM-M901D power module or its analogs using STR-W6253 microcircuits.
MainBoard - the main board (motherboard) is an EAX62848101 module, using the LMD9201A-LF-SD, AP1W084D, 1006B, K4T51163QG-HCF7, 24C512, 24C08W, MX25L12845EM, LGE40RC-LF, WJCE6355C590, MAX322, MAX232, IC2 chip APW7080, LM324G, AZ1117D, AZ1085Z and others.
Additional technical information about the panel:
Brand: CMO
Model: M270H1-L01
Type: a-Si TFT-LCD, Panel
Diagonal size: 27.0 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 597.888x336.312 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit)
Response Time: 0.8 / 2.6 (Tr / Td)
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V