Technical description and composition of the SONY KD-55XE8096 TV, panel type and applicable modules. The composition of the modules.SONY LED
Model: KD-55XE8096
Chassis / Version: BMK S
Panel: V550QWSE09
LED backlight: STO550AN5_51LED R / L REV0
T-CON: 6870C-0704A 6871L-4907A
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): APDP-209A1 Adapter AC / DC 19.5V 209W
MainBoard: 1-981-326-12 173633712 YA03012AA
IC MainBoard: CPU, NAND Flash, Audio
Tuner: CE551ZP
Technical Specifications KD-55XE8096
SONY KD-55XE8096
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SONY KD-55XE8096 TV does not turn on at all. The control lights do not light or flash. The TV on the remote control and the control panel buttons do not respond.
With such manifestations, a malfunction is most likely to be detected in the APDP-209A1 power supply module.
The owner of a TV set usually purchases an external power source such as APDP-209A1 Adapter AC / DC 19.5V 209W on its own, it often happens that its repair is impractical, but the simplest defects that are characteristic of IIPS can be seen and easily fixed after opening. It is then necessary to measure its output voltages and, if they are absent, it is necessary to check the power switches and rectifier diodes of the converters for a short-circuit probability.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn on and immediately disappears
The most likely in these cases is a malfunction of the LED backlight. Usually the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver also turns out to be faulty.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the motherboard 1-981-326-12 should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips, NAND Flash, Audio and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the CE551ZP tuner may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention! For users and owners of KD-55XE8096 TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-serviceability of the device.
The appearance of MainBoard 1-981-326-12 is shown in the figure below:1-981-326-12
The appearance of the power supply
Main features of the device SONY KD-55XE8096:
Installed matrix (LED-panel) V550QWSE09.
The matrix control uses the Timing Controller (T-CON) 6870C-0704A.
To power the backlight LEDs, a converter is used, combined with the main board 1-981-326-12.
To power all the internal components of the SONY KD-55XE8096 TV, an external source of the APDP-209A1 Adapter AC / DC 19.5V 209W type is used.
MainBoard - the main board (motherboard) is a module 1-981-326-12, with the use of CPU chips, NAND Flash, Audio and others.
The CE551ZP tuner provides TV reception and channel tuning.
Brand: SONY, Model: KD-55XE8096.
Shortly from the TV: LCD, LED backlight, 55 ", 3840x2160, 4K UHD, HDR, TFT IPS, DVR, there is a satellite tuner, sound: 20W, HDMI connectors: 4, Internet access, Wi-Fi, Bluetooth, Smart TV.
On the official website of Sony there is firmware (Firmware) - software update to version 6.6520 from 06/30/2019.
The composition uses MainBoard 1-981-326-12 173633712 YA03012AA and LCD-panel V550QWSE09.
External power supply APCP-209A1 Adapter AC / DC 19.5V 209W.
SONY KD-55XE8096 TV with V550QWSE09 LCD display, 55 "(140 cm) diagonal size in 16: 9 format. This model uses side illumination from Edge LEDs.
The V550QWSE09 display and software (software) of the 1-981-326-12 board provide viewing in high quality UHD 4K at a resolution of 3840x2160 pixels in the standard 4K UHD, HDR. Image processing is performed using modern High Dynamic Range (HDR) technologies with an extended range of brightness gradations.
The KD-55XE8096 TV has built-in SMART Software and pre-installed Android Operating System. Connecting to the Internet can be done via Wi-Fi. Video processor supported multimedia file formats: MP3, WMA, MPEG4, HEVC (H.265), Xvid, DivX, MKV, JPEG.
The power of the sound speaker system 20 W (2x10 W) is provided by two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV x2, component, HDMI x4, USB x3, Ethernet (RJ-45), Bluetooth, Wi-Fi 802.11n, WiDi, Miracast . An output for connecting headphones is provided.
The digital tuner is capable of receiving television channels in the standards DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2.
The power consumed by the TV in the operating mode from the network is 166 watts.
Overall dimensions: with stand 1232x772x252 mm, without stand 1232x716x57 mm.
TV Weight: with stand: 18.6 kg, without stand: 17.6 kg.
Attention! The V550QWSE09 panel of the SONY KD-55XE8096 LED TV is its most expensive element.
Avoid hitting the glass and excessive pressure on the screen surface to avoid damage to the LED panel!
It is unsafe to get any liquid on the screen. Sometimes one drop of water is enough, if it flows down the glass onto the cables, the TV can become unrepairable.
