
SONY
Model: KDL-26S2010
Chassis / Version: WAX2
Panel: LTY260W2-L1
T-CON: 260w3c4lv2.5.
Inverter (backlight): CSN304-00 A06-126290E PCB2680 26
PWM Inverter: BD9886FV
MOSFET Inverter: RSS070N05
Power Supply (PSU): APS-220 - 1-869-132-31 - 1-468-980-13
PWM Power: FA5501AN (PFC), MIP2H2, CXD9841M
MOSFET Power: 2SK3561, 2SK3934
MainBoard: 1-869-850-15
IC MainBoard: CXA2069, MSP4410
Tuner: BTD-HF431Z TUNER BOARD 1-869-657-12
Technical Specifications KDL-26S2010
SONY KDL-26S2010
General recommendations for repairing TV LCD
Like any other TV, SONY KDL-26S2010 it is advisable to start repairing with an external inspection for visible changes in the external and internal elements. Many visible signs make it possible to determine the future direction of troubleshooting and localization of the defect. In most cases, the repairman can guess the causes of the defect and possible consequences by the characteristic signs of typical TV defects, for example, ring cracks formed in the soldering of element leads, swollen rectifier filter capacitors, charred resistors and other circuit elements.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, does not make any sounds or any signs of operability when turned on, there is a certain probability that the power module is defective and needs repair. Sometimes with similar manifestations a problem can only occur in the absence of processor power, but this happens much less often. The diagnostics of the power supply should always be started by checking the fuse and, if it is broken, it is first necessary to check the rectifier bridge diodes and the power switch for the likelihood of an avalanche or thermal breakdown.
Power switches in flyback converters fail extremely rarely for no reason and, if they are broken, it is necessary to look for a malfunction in the stabilization circuits by checking electrolytic capacitors, semiconductor devices, and resistors in the primary circuit. The cause may be a malfunction of the PWM controller chip, which can only be checked by replacing it with a new or obviously working one.
When using a power factor correction unit (PFC) in the power modules, troubleshooting becomes somewhat more complicated and requires additional experience and knowledge of their operation.
Sometimes the SONY KDL-26S2010 TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the backlight converter, or of the lamps themselves, which can be checked by replacement. In such cases, it is necessary to verify the serviceability of all electrolytic capacitors of the filter according to the power supply of the inverter itself, including the power supply unit (power supply unit).
When repairing the CSN304-00 A06-126290E PCB2680 26 inverter, it is often necessary to disable the protection for diagnostics, which, for fire safety reasons, turns it off in any emergency situation, for example, during a malfunction or uneven wear of the lamps, which makes it difficult to find a defect.
Turning off the protection for diagnostic purposes, it must be remembered that in this case there is a risk of failure of the power elements of the inverter. Upon completion of the diagnosis, all regular protection circuits should be restored.
In cases of attempts to repair the motherboard 1-869-852-12, it is necessary to check the operability of the power stabilizers of the microcircuits and, if possible, update the software (software). When repairing an MB board, you need to check its components CXA2069, MSP4410. Defective items should be replaced.
If there is no reception of television channels, but the TV is working properly from external devices, first of all you need to check the voltage of the varicaps of the tuner BTD-HF431Z TUNER BOARD 1-869-657-12, which is usually within 30-33V, as well as other power voltage at the terminals of the tuner.
Remember! Attempts to self-repair by users of the SONY KDL-26S2010 TV without the appropriate qualifications and the necessary experience can lead to serious negative consequences!
Service manual / schematic diagram -------------------> Sony KDL-23S2010, KDL-26S2010, KDL-32S2010, KDL-40S2010, KDL-46S2010 CHASSIS WAX2
Service manual / schematic diagram -------------------> Sony KDL-26S2000, KDL-32S2000, KDL-40S2000, KDL-46S2000, KDL-26S2010, KDL-32S2010, KDL-40S2010, KDL-46S2010, KDL-26S2020, KDL-32S2020 CHASSIS WAX2
PSU schematic diagram -------------------> Sony APS-220 Power supply

1-869-850-15
1-869-850-15 can be used on TVs:
SONY KDL-26S2010 (Panel LTY260W2-L1), SONY KDL-32S2000 (Panel LTZ320WS-L05), SONY KDL-40S2530 (Panel LTY400WT-LH1), SONY KDL-46S2530 (Panel LTY460WT-LH3).
The appearance of the power supply
Main features of the device SONY KDL-26S2010:
Installed matrix (LCD-panel) LTY260W2-L1.
The matrix control uses the Timing Controller (T-CON) 260w3c4lv2.5 ..
To power the backlight, an inverter CSN304-00 is used, it is controlled by the BD9886FV PWM controller. As power elements of the inverter, keys of type RSS070N05 are used.
The necessary supply voltages for all nodes of the SONY KDL-26S2010 TV are generated by the APS-220 power supply module or its analogs using FA5501AN (PFC), MIP2H2, CXD9841M microchips and power switches of the type 2SK3561, 2SK3934.
MainBoard - the main board (motherboard) is a module 1-869-850-15, using CXA2069, MSP4410 and others.
Tuner BTD-HF431Z TUNER BOARD 1-869-657-12 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: S-LCD
Model: LTY260W2-L16
Type: a-Si TFT-LCD, Panel
Diagonal size: 26.0 inch
Resolution: 1366x768, WXGA
Active Area: 575.769x323.712 mm
Frequency: 60Hz
Lamp Type: CCFL