SONY
Model: KDL-26V4000
Chassis / Version: NEX
Panel: LTA260AP01 Y01
Inverter (backlight): INV26S10A
PWM Inverter: OZ9966SN (24pin)
MOSFET Inverter: AOD486A
Power Supply (PSU): 1-876-635-11 - A1556796A GA2
PWM Power: MCZ3001DB (18pin), MIP2H2 (8pin)
MainBoard: 1-875-656-22 - Y2008460K - A1544037K
IC MainBoard: MB90F334, K9F5608U0D, CXB1444R, TPA3100D2
Tuner: BTF-HF412T
Technical Specifications KDL-26V4000
SONY KDL-26V4000
General recommendations for repairing TV LCD
Repair SONY KDL-26V4000 must begin with the diagnosis of the malfunction and a thorough inspection of its external and internal components, including those of the body. Many visible signs make it possible to determine the future direction of troubleshooting and localization of the defect. Carbonized paint on the upper layer of resistors, electrolytic capacitors of rectifier filters swollen after boiling, cracked soldering at the terminals of heating elements or transformers can often suggest the cause of the defect and possible consequences.
In the absence of any signs of operability, when the SONY KDL-26V4000 does not turn on and does not signal anything with the control lights on the panel, the GA2 M1526430A power supply module is most likely faulty. When diagnosing and repairing the GA2 M1526430A power supply, it is first necessary to check the fuse, and if it breaks, the power switch and rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
If a breakdown of the power switch of the flyback converter of the power supply unit is detected, it should be remembered that it does not fail without any reasons that should be sought by checking other elements of the primary circuit - electrolytic capacitors, PWM controller MCZ3001DB (18), MIP2H2 (8), which You can check only by replacement, as well as other semiconductor elements (diodes, transistors, zener diodes).
Diagnostics of power modules with a Power Factor Corrector (CMC) is somewhat more complicated and requires a more detailed approach.
If the SONY KDL-26V4000 does not have an image, but there is sound, there is a possibility of a malfunction of the backlight or power converter. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
The operation of the power circuits of the inverter and the backlight in the normal mode are controlled by special protection, which is organized for fire safety, for example, to disconnect during short circuits or breaks in high-voltage connections or when the lamps are depressurized. This protection makes it difficult to diagnose and repair the inverter.
It should be remembered that when the protection is turned off, there is always a risk of failure of the power elements of the inverter during diagnosis. After repair, it is necessary to restore all standard converter protection circuits.
Before replacing the BTF-HF412T tuner, if there is no tuning for the channels, you must first check the supply voltage at its terminals, including the varicap supply (30-33V).
Owners and users of the SONY KDL-26V4000 TV must remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
Service manual / schematic diagram -------------------> Sony KDL-26V4000, KDL-32V4000, KDL-37V4000 CHASSIS SE2AG
PSU schematic diagram -------------------> Sony 1-876-635-12, 1-876-635-11 Power supply
The appearance of MainBoard 1-875-656-22 is shown in the figure below:
1-875-656-22
1-875-656-22 can be used in TVs:
SONY KDL-26V4000 (Panel LTA260AP01 Y01), SONY KDL-37V4500 (Panel T370XW02 V.C), SONY KDL-32V4500 (Panel LTZ320AA01).
The appearance of the power supply
Main features of the device SONY KDL-26V4000:
Installed matrix (LCD-panel) LTA260AP01 Y01.
The INV26S10A inverter is used to power the backlight, controlled by the OZ9966SN PWM controller (24pin). As power elements of the inverter, keys of the AOD486A type are used.
The necessary supply voltages for all nodes of the SONY KDL-26V4000 TV are generated by the power module 1-876-635-11, or its analogs using microchips MCZ3001DB (18pin), MIP2H2 (8pin).
MainBoard - the main board (motherboard) is a module 1-875-656-22, using microchips MB90F334, K9F5608U0D, CXB1444R, TPA3100D2 and others.
The BTF-HF412T tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTA260AP01
Type: a-Si TFT-LCD, Panel
Diagonal size: 26.0 inch
Resolution: 1366x768, WXGA
Display Mode: APVA, Normally Black, Transmissive
Active Area: 575.769x323.712 mm
Surface: Antiglare (Haze 14%), Hard coating (3H)
Brightness: 450 cd / m²
Contrast Ratio: 2000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 8 (G to G)
Frequency: 60Hz
Lamp Type: 5 pcs CCFL Embedded (Inverter)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V