SONY
Model: KDL-52Z4500
Chassis / Version: EG1L_200Hz
Panel: 52 inch
Inverter (backlight): G6 board + SSB520H24S01 Rev0.1
Trans Inverter: BL-52S B0805A
Power Supply (PSU): 1-877-271-12 - A1653731B G6, 1-876-294-12
PWM Power: MM3313AF, MIP2H2, CXD9841P
MOSFET Power: 2SK3561
MainBoard: 1-877-366-13 - A-1184-536-C - E1599852E
IC MainBoard: CXD9926ATQ, CXD9926ATQ, TPA3100D2
Technical Specifications KDL-52Z4500
SONY KDL-52Z4500
General recommendations for repairing TV LCD
Repair of a SONY KDL-52Z4500 TV is advisable to start with an external examination of all its constituent elements, both internal electronic components and external. Inspection is also subject to body elements, control buttons, screen, connectors and cords. Visible damage to elements can sometimes suggest further directions for finding a defect before starting the necessary measurements. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
If the G6 power supply module fails, the external manifestations may be different, for example, the SONY KDL-52Z4500 does not turn on at all and there is no indication of the control lights on the front panel. When diagnosing and repairing the G6 power supply unit, it is necessary first of all to check the fuse, and if it breaks, the power switch and rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
It should be remembered that the N-FET keys used in flyback converters rarely fail for no reason that must be sought by checking other elements of the circuit. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The PWM controller chip can also cause a breakdown of the power switch of the converter.
In cases using a power module with an active KKM, troubleshooting is sometimes somewhat more complicated.
If, when you turn on the TV, the image appears and immediately disappears, or is initially absent when you turn on, but there is sound and other functions work, there is a high probability of a malfunction of the inverter (power converter for the backlight). In such cases, the lamps, the inverter and the common power module are subject to verification, in which the electrolytic capacitors of the rectifier filter supplying the inverter should be checked.
When repairing the inverter D4, D5, it is often necessary to disable the protection for diagnostics, which, for the purpose of fire safety, turns it off in any emergency situation, for example, during a malfunction or uneven wear of the lamps, which makes it difficult to find a defect.
It should be remembered that in such cases there is a risk of failure of the power elements of the inverter and to take special care. After carrying out repairs, the protection circuit must be restored for further safe operation of the TV.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Trust the repair only to professionals with sufficient experience in the field of electronic equipment repair.
Service manual ----------> Sony KDL-40Z4500, Sony KDL-46Z4500, Sony KDL-52Z4500 Chassis EG1L
Service manual -----------> Sony 1-877-271-12 G6 board Power supply
The appearance of MainBoard 1-877-366-13 is shown in the figure below:
1-877-366-13
1-877-366-13 can be used in TVs:
SONY KDL-40W4500 (Panel LTY400HC02 001), SONY KDL-52Z4500 (Panel 52 "), SONY KDL-40Z4500 (Panel LTY400HG01).
The appearance of the power supply
Main features of the device SONY KDL-52Z4500:
Installed matrix (LCD-panel) 52 inches.
To power the backlight used inverter G6. A transformer BL-52S B0805A is installed in the inverter converter.
The necessary supply voltages for all nodes of the SONY KDL-52Z4500 TV are generated by the power module 1-877-271-12, or its analogs using microcircuits MM3313AF, MIP2H2, CXD9841P and power switches of the type 2SK3561.
MainBoard - the main board (motherboard) is a module 1-877-366-13, using CXD9926ATQ, CXD9926ATQ, TPA3100D2 and others.