Technical description and composition of the FUSION FLTV-32L41B TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-32L41B
Chassis / Version: TP.VST59.P83
Panel: DBMS315LK09-C
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: LD7536
MOSFET Power: N-FET 600V 7A
MainBoard: TP.VST59.P83
IC MainBoard: CPU: TSUMV59XE Spi Flash: W25Q32BV
Tuner: CDT-3NP5I1-10
Technical Specifications FLTV-32L41B
FUSION FLTV-32L41B
General repair guidelines for TV LCD LED
The FUSION FLTV-32L41B TV, like many other electronic devices, it is advisable to start repairing by inspecting all external and internal elements. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. If charred resistors, swollen electrolytic or cermet capacitors, ring cracks in the solders of the terminals of transformers or heating elements are found, it is advisable to establish the causes and consequences of the malfunction that has arisen, as well as to check the connected elements and assemblies.
Malfunctions of the power module can be expressed in different ways, for example, the FUSION FLTV-32L41B does not turn on at all and the control lamps on its front panel do not light up and do not blink, there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. When repairing the power supply, it is advisable to start the diagnostics by checking the mains fuse and the electrolytic capacitors of the filters of the converter secondary rectifiers. In the event of a fuse breaking, the reason should be sought in the power semiconductor elements of the pulse converter of the main power supply. First of all, it is necessary to check the diodes of the bridge of the rectifier of the mains voltage and the power switch (s) of the converter.
In most cases, key breakdowns in switching power supplies (SMPS) do not occur for no reason and you should look for other faulty circuit elements that could provoke a defect. This can be dried electrolytic capacitors in the primary circuit, and faulty damper elements, as well as dangling resistors or punched semiconductor elements in the stabilization circuits. Possible defective PWM chip from the manufacturer.
If the FUSION FLTV-32L41B does not have an image, but there is sound, there may be a malfunction of the backlight LEDs of the panel or their power converter. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
To check the health of the LEDs and contact connections in their power circuit, it is necessary to disassemble the panel.
An open in the line of LEDs connected in series cannot be detected with a multimeter or tester without disassembling the panel. To open all the transitions, several tens of volts are needed, and it is best to use a current source for such purposes.
In cases of attempts to repair the TP.VST59.P83 motherboard, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - Cpu: TSUMV59XE Spi Flash: W25Q32BV with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
If you suspect a malfunction of the tuner CDT-3NP5I1-10, first of all, you need to make sure that the voltage of the varicaps (30-33V) is present on the corresponding output of the tuner, as well as other voltage supplying it.
Once again, remind users! Attempts to independently repair the FUSION FLTV-32L41B TV without the appropriate qualifications and experience can lead to its complete non-repairability!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> TP.VST59.P83-65W18
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-32L41B, Main: TP.VST59.P83
At failures in the software SPI FLASH chip manufacturer Winbond, they can at any time to restore its efficiency after temperature exposure - warm hairdryer soldering station, or even lighter. Usually this is enough to read the regular contents of the software. In such cases, the chip must be replaced with a new one.
Repair MainBoardThe appearance of MainBoard TP.VST59.P83 and voltage measurements at the test points are shown in the figure below:
TP.VST59.P83
The TP.VST59.P83 motherboard is combined with a power module and is an independent device made on the basis of the TSUMV59Xxx multifunction processor. Repair of such a board must begin by checking the power batteries, as well as the operability of the voltage converters and linear stabilizers necessary to provide power to certain processor nodes, in particular: + 1.2V core power, built-in DDR + 1.8V memory, and Stand- by 3.3V. The voltage of the LCD panel 5V or 12V, depending on the type of panel used, must be checked directly on the LVDS connector.
TP.VST59.P83 can be used on TVs:
AKAI LEA-28A08W (Panel ST2751A01-1), ERISSON 39LEN52 (Panel TLV3931-02), ERISSON 32LEN52 (Panel TLV3231-01), FUSION FLTV-32L28B (Panel TH315B051-MD1), FUSION FLTV-39LF28B (Panel V390HJ1-P02), FUSION FLTV-32L41B (Panel DBMS315LK09-C), FUSION FLTV-40LF28B (Panel DBMS400LK01-A), HYUNDAI H-LED32V18 (Panel CX315DLEDM T320XVN02.A ), MYSTERY MTV-4023LW (Panel CX390DLEDM / T390HVN04.0), ROLSEN RL-39D1305F (Panel V390HJ1-P02 Rev. C1), RUBIN RB-32D3U (Panel T320XVN01.0), RUBIN RB-39D3F (Panel CX390DLEDM), SHIVAKI STV-40LED5 (Panel V390HJ1-P01 Rev C1), SUPRA STV-LC3225AWL (Panel TH315B051-MD2), SUPRA STV-LC32T810WL (Panel TC315F3E5-A), SUPRA STV-LC32880WL (Panel HE315GH-E77GM\PW1 ), SUPRA STV-LC2825WL (Panel SM275TC30), SUPRA STV-LC32820WL (Panel TC315FJE1-MD4), SUPRA STV-LC32810WL (Panel TC315F3E5-A), TELEFUNKEN TF-LED32S7 (Panel ST3151A05-5 CX315DLEDM).
Main features of the FUSION FLTV-32L41B device:
Installed matrix (LED-panel) DBMS315LK09-C.
To power the backlight LEDs, a converter is used, combined with the main board TP.VST59.P83, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using LD7536 microcircuits and power switches of the N-FET 600V 7A type.
MainBoard - the main board (motherboard) is TP.VST59.P83 module using Cpu Chipset: TSUMV59XE Spi Flash: W25Q32BV and others.
The tuner CDT-3NP5I1-10 provides the reception of television programs and tuning to channels.
FUSION FLTV-32L41B TV with DBMS315LK09-C LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 350 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 80000: 1 is achieved by special control of the LEDs The LED-panel of this TV is equipped with LED end-lighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM , NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, MKV, JPEG.
The power of the sound system 16 W (2x8 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV working in the network mode is 90 watts.
Overall dimensions: 850x570x130 mm.
Attention! The DBMS315LK09-C panel of the FUSION FLTV-32L41B LED TV is an expensive and unreliable element.
Avoid any knocks on the glass and the pressure on the surface of the screen in order to avoid damage to LED-bar!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
