Technical description and composition of the SUPRA STV-LC32ST900WL TV, panel type and modules used. The composition of the modules.SUPRA LED
Model: STV-LC32ST900WL
Chassis / Version: V1R07
Panel: HK315LEDM-OHFCH
LED backlight: HK32D10A-ZC21A-03 303HK320031
T-CON: CV320PW03S
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: AOD4454
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 (LD7536)
MOSFET Power: SMK10N60
MainBoard: CV628H-T42 BASE-CV628H_T42-V009
IC MainBoard: CPU: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2
Tuner: CDT-9NT372-RF01 MSB102KT
STV-LC32ST900WL Specifications
SUPRA STV-LC32ST900WL
General recommendations for TV LCD LED repair
Possible manifestations of defects
- SUPRA STV-LC32ST900WL TV does not turn on at all. Control lamps do not light up or blink. The TV on the remote control and control panel buttons does not respond.
A malfunction in such cases should be looked for in the elements of the power source - the mains voltage converter (AC / DC), which is located on the MainBoard CV628H-T42. It is necessary to make sure that its output voltages are present and, if they are completely absent, check the power switches (SMK10N60) and rectifier diodes for a possible short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in an emergency mode of a short circuit, and with a short circuit in the power elements of the primary circuit, the mains fuse or current sensor in the source of the key is often cut off.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can disable it in the key mode, or create an excess of the maximum permissible key parameters. These can be elements supplying a PWM regulator, frequency setting or damper circuits, or elements of negative feedback in the stabilization circuit. PWM controllers PWM SOT23-6 (LD7536), in the absence of visible damage or outright short circuits between the terminals, are checked by replacing them with new ones, or knowingly working properly.
- There is no picture, there is sound, it reacts to the remote control, the channels are switched. In some cases, the image appears when turned on and disappears immediately.
In such cases, the most likely malfunction of the LED panel backlighting elements. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
Without a special current source, it is impossible to check the line of LEDs connected in series, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Typically, Chinese multimeters with a 9V power supply lightly light up one 3-volt LED, if you connect the probes to it in the forward direction, the red probe to the anode, and the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or broken into the K / Z.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the CV628H-T42 motherboard should begin with checking the stabilizers and power converters required to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Often the MB (SSB) board needs to be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2 and replace the failed chips with new ones. Some malfunctions may be associated with the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
Before changing the CDT-9NT372-RF01 tuner, if it is not possible to tune to TV channels, you should make sure that there are supply voltages, which must be measured at the corresponding tuner terminals and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be monitored with an oscilloscope
Attention to TV owners! Attempts to repair SUPRA STV-LC32ST900WL yourself are not recommended by the manufacturer and can lead to serious negative consequences!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL --------> BBK 32LEX-5009 Chassis CV628H-T42
The appearance of the MainBoard CV628H-T42 is shown in the figure below:CV628H-T42
CV628H-T42 can be used in TVs:
BBK 43LEX-5009/FT2C (Panel LC430DUY (SH)(A1)), BBK 40LEX-5025/FT2C (Panel V400HJ6-PE1 DLEDSV400FHD), BBK 32LEX-5027/T2C (Panel V320BJ6-Q01 Rev.C1), SUPRA STV-LC40ST900FL (Panel V400HJ6-PE1).
Main features of SUPRA STV-LC32ST900WL device:
Installed matrix (LED panel) HK315LEDM-OHFCH.
Matrix control uses the Timing Controller (T-CON) CV320PW03S.
To power the backlight LEDs, a converter combined with the CV628H-T42 main board is used, controlled by the BIT3267 PWM controller. The keys of the AOD4454 type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter circuit using PWM SOT23-6 (LD7536) microcircuits and power switches of the SMK10N60 type.
MainBoard - the main board (motherboard) is a Cultraview CV628H-T42 module using CPU chips: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2 and others.
Tuner CDT-9NT372-RF01 MSB102KT provides reception of television programs and tuning to channels.
SUPRA LED TV STV-LC32ST900WL with LCD display HK315LEDM-OHFCH, 32 "(81 cm) 16: 9. operation of LEDs depending on the illumination of areas in the scene.The technology of manufacturing the display model uses LED LED backlighting.It is possible to view programs and films and images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready).
STV-LC32ST900WL has built-in SMART software and pre-installed Android operating system. Internet connection can be made via Wi-Fi wireless connection. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
Speaker power 12 W (2x6 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x2, USB x3, Ethernet (RJ-45), Wi-Fi. A headphone output is provided. The digital tuner is capable of receiving TV channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Dimensions: With stand 1235x758x284 mm, Without stand 713x435x86 mm.
Attention! The HK315LEDM-OHFCH panel of the SUPRA STV-LC32ST900WL LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it flows down the glass onto the cables to make the TV non-repairable ...........................
