Technical description and composition of the SUPRA STV-LC39663FL TV, panel type and modules used. The composition of the modules.SUPRA LED
Model: STV-LC39663FL
Chassis / Version: V1L09
Panel: V390HJ1-P01
MainBoard: 5800-A8M480-0P10 (VER.00.07)
IC MainBoard: FLASH: EN25Q32
Tuner: ET-9Z2E-CF106H
Control: Login to service: SOURCE 3195
STV-LC39663FL Specifications
SUPRA STV-LC39663FL
General recommendations for TV LCD LED repair
Repair of electronic equipment usually begins with its external examination and diagnosis of a malfunction. In this case, you should inspect all the internal components of the SUPRA STV-LC39663FL TV, as well as the external elements of the case. Based on visible external changes in the state of components, it is usually possible to determine the further direction of troubleshooting and localization of a defect before taking the necessary measurements. Swollen electrolytic or sintered capacitors, charred resistors, ring cracks in the soldering of the element terminals - all this can significantly help the master to determine the causes and consequences of the malfunctions in the TV.
In the case when the STV-LC39663FL does not turn on, does not respond to the remote control and front panel buttons, does not blink lights and does not show any signs of operability, the power module is probably faulty in this case. If it is working properly with such manifestations, it is necessary to check the processor power regulator (converter) on the motherboard. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse in the power supply is broken, in most cases a breakdown of the power switch (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. You should also check the diodes of the rectifier bridge and the electrolytic capacitor of the mains rectifier filter.
Mos-Fet switches used in switching power supplies (SMPS) rarely fail without reasons that must be looked for by checking other circuit elements. Breakdown is often caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or breakdown of resistors in stabilization circuits. The PWM controller microcircuit can also cause the breakdown of the power switch of the converter.
Sometimes the SUPRA STV-LC39663FL TV does not have a picture, but there is sound, or the picture appears and immediately disappears. In this case, there is a high probability of a malfunction of the V390HJ1-P01 panel backlight LED converter, or an open circuit in the LED circuit is possible. In such cases, first of all, it is necessary to make sure that all electrolytic capacitors of the filter are in good working order for the power supply of the LED driver itself, including the power supply unit (power supply unit).
In most cases when there is no backlight, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or more LEDs do not work in one line, therefore, they are punctured and should be replaced.
It should be remembered that it is not possible to determine an open circuit in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
In cases of an attempt to repair the motherboard 5800-A8M480-OP10 (VER.00.07), it is necessary to check the performance of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
In cases of attempts to repair the MB (SSB) board, it is necessary to check the serviceability of its elements - FLASH: EN25Q32 which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its pins with the board (indicated by warming up).
Before changing the ET-9Z2E-CF106H tuner, if it is not possible to tune to TV channels, you should make sure that there are supply voltages, including the power supply for varicaps (30-33V), which must be measured at the corresponding terminals of the tuner.
Remember! Attempts to self-repair the SUPRA STV-LC39663FL TV by users without appropriate qualifications and the necessary experience can lead to serious negative consequences!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> SUPRA STV-LC39663FL (V1L09), Main 5800-A8M480-0P10, Panel: V390HJ1-P01
If the SPI FLASH Winbond software fails, we recommend replacing the microcircuit with a new one. In addition, faulty Winbond microcircuits can sometimes recover for a while after warming up with a soldering station or even a lighter, which is enough to read its standard contents.
Additional MainBoard RepairThe appearance of the MainBoard 5800-A8M480-0P10 is shown in the figure below:
5800-A8M480-0P10
5800-A8M480-0P10 can be used in TVs:
AIWA 47LE61103 (Panel LC470EUN (SE)(F1)), AIWA 42LE6110 (Panel LC420EUN (SE)(M1)), AIWA 39LE6110 (Panel V390HJ1-P01), ERISSON 42LES66 (Panel LC420EUN SEM1), ERISSON 39LES66 (Panel CX275DLEDM), ERISSON 32LES66 (Panel REL320AH-U100 Rev.00), SUPRA STV-LC39660FL (Panel V390HJ1 rev.c1 SEL390V7-S00D ), SUPRA STV-LC32663FL (Panel T320HVN01.2), SUPRA STV-LC39663FL (Panel V390HJ1-P01), SUPRA STV-LC47660FL00 (Panel LC470EUN).
Main features of SUPRA STV-LC39663FL device:
Installed matrix (LED panel) V390HJ1-P01.
The required supply voltages for all nodes of the SUPRA STV-LC39663FL TV are provided by a switching power supply.
MainBoard - the main board (motherboard) is a 5800-A8M480-0P10 module, using FLASH chips: EN25Q32 and others.
Tuner ET-9Z2E-CF106H provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: ChiHsin
Model: V390HJ1-P01
Type: a-Si TFT-LCD, CELL
Diagonal size: 39 inch
Resolution: 1920x1080, FHD
Display Mode: MVA, Normally Black, Transmissive
Active Area: 853.92x480.33 mm
Surface: Antiglare (Haze 3.5%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 5.6% (with Polarizer)
Contrast Ratio: 5000: 1
Display Colors: 16.7M (8-bit)
Response Time: 8 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
SUPRA LED TV STV-LC39663FL with LCD V390HJ1-P01, diagonal 39 "(99 cm) in 16: 9 format. This model uses an LED panel with edge LED backlighting - Edge LED. and movies in high quality HD at a resolution of 1920x1080 pixels in graphic decomposition according to the standard 1080p (Full HD) .Input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. Graphic processing and formation of a digital signal occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Supported media file formats: MP3, MPEG4, MKV, JPEG Stereo sound is provided by two built-in speakers Uses NICAM STEREO audio processing system.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, USB x2. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768, 1920x1080.
Dimensions: With stand 794x561x204 mm, Without stand 794x499x90 mm.
Attention! SUPRA STV-LC39663FL LED TV panel V390HJ1-P01 is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV non-repairable.
