Technical description and composition of the SUPRA STV-LC42T650FL TV, panel type and modules used. The composition of the modules.SUPRA LED
Model: STV-LC42T650FL
Chassis / Version: V1R10
Panel: C420F16-E14-C (G11)
LED backlight: 303TT416036 0D416D09-ZC21AG-04
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
MOSFET LED driver: AOD458
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-220
MainBoard: TP.MS3463S.PB801
IC MainBoard: CPU: MSD3463GU, SPI Flash: 25Q64CSIG, SOUND: OB6220VP
Tuner: XF-3SDT-H (R840)
STV-LC42T650FL Specifications
SUPRA STV-LC42T650FL
General recommendations for TV LCD LED repair
Possible malfunctions
- SUPRA STV-LC42T650FL TV does not turn on at all. Control lamps do not light up or blink. The TV on the remote control and control panel buttons does not respond.
A malfunction in such cases, first of all, should be looked for in the power elements of a switching power supply (SMPS) - a mains voltage converter (AC / DC), which in this TV model is combined with the main board MainBoard TP.MS3463S.PB801. It is necessary to measure its output voltages, and if they are absent (full or partial), the serviceability of the power switches (TO-220) of the converters and rectifier diodes should be checked for a possible short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can operate in an emergency mode in a short-circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse is usually cut off.
Breakdown of Mos-Fet switches used in switching power supplies is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM regulator, in frequency-setting or damper circuits, as well as in negative feedback stabilization. PWM microcircuits (PWM) PWM SOT23-6 are usually checked by replacing them with new ones, or knowingly working.
- There is no image, the screen is black, there is sound, when the screen is illuminated outside, you can sometimes see barely noticeable outlines of the image.
The malfunction in most of these cases is found in the nodes and elements of the LED panel backlighting. The reason may be in the breakage of the LEDs, in the stabilization of their power supply, or in the violation of the contact connections of the strings connectors,
Without a special current source, it is impossible to check the line of LEDs connected in series, and it is unsafe for them to use any voltage sources above 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Typically, Chinese multimeters with a 9V power supply lightly light up one 3-volt LED if you connect the probes to it in the forward direction, the red probe to the anode, and the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or broken into the K / Z.
- TV does not turn on, does not respond to the remote control. The indicator blinks or signals the standby mode.
Repair or diagnostics of the TP.MS3463S.PB801 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). When repairing an MB board, you need to check its components CPU: MSD3463GU, SPI Flash: 25Q64CSIG, SOUND: OB6220VP. Defective elements must be replaced. If chips with BGA soldering technology are used, the problem in its implementation is detected by local heating of the chip.
If the TV operates normally from external devices, but does not tune into TV channels, the XF-3SDT-H (R840) tuner may be faulty. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the data exchange between the tuner and the processor is possible via the I2C bus. Sometimes the reason for the inoperability of the tuner may be a software failure.
Remember! Attempts to self-repair the SUPRA STV-LC42T650FL TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL AND
Trouble Shooting ------------------> Chassis TP.MS3463S.PB801
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> SUPRA STV-LC42T650FL V1R10 , Main: TP.MS3463S.PB801, Panel: C420F16-E14-C (G11)
The appearance of the MainBoard TP.MS3463S.PB801 is shown in the figure below:TP.MS3463S.PB801
TP.MS3463S.PB801 can be used in TVs:
AKAI LEA-40V35M (Panel LSC400HM06), AKIRA 32LED38T2P (Panel ST3151A05-8), AKIRA 32LED02T2M (Panel ST3151A04-9 Ver.2.1), BBK 32LEM-1029/TS2C (Panel C320X16-E18-H), BBK 39LEM-1033/TS2C (Panel C390X15-E8-A G01), BBK 32LEM-1026/TS2C (Panel CX315DLEDM ST3151A05-8), BBK 32LEM-1027/TS2C (Panel ST3151A05-8 / CX315DLEDM), DEXP F43C7100K (Panel LC430DUY (SH)(A1)), DEXP F42B7000M (Panel V420HJ2-P01), DEXP F43C7000C (Panel C430F14-E1-L / LC430DUY), DEXP F40B7100K (Panel LSC400HN02-G02 40N06-L-HPX1F1), DEXP H28C7100C (Panel C275X15-E1-H (G31)), DEXP H32C7300K (Panel LSC320AN02), DEXP H32D7100C (Panel ST3151A05-8 Ver2.5), DEXP H28D7300K (Panel HV280WX2-260), ERISSON 32LES78T2W (Panel KM0320LDRH0037), ERISSON 32LEE30T2 (Panel LK315T3HB87-12V), SUPRA STV-LC32T560WL (Panel LSC320AN10), SUPRA STV-LC32T550WL (Panel LSC320AN02), SUPRA STV-LC40T500WL (Panel C39X15-E7-A), TELEFUNKEN TF-LED32S45T2 (Panel LK315T3HB87-12V), THOMSON T39D20DH-01B (Panel T390XVN01.0).
Main features of SUPRA STV-LC42T650FL device:
Installed matrix (LED panel) C420F16-E14-C (G11).
To power the backlight LEDs, a converter combined with the TP.MS3463S.PB801 main board is used, controlled by the SN51DP PWM controller. The keys of the AOD458 type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and TO-220 type power switches.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB801 module using CPU chips: MSD3463GU, SPI Flash: 25Q64CSIG, SOUND: OB6220VP and others.
Tuner XF-3SDT-H (R840) provides reception of television programs and tuning to channels.
SUPRA LED TV STV-LC42T650FL with LCD C420F16-E14-C, 42 "(107 cm) 16: 9 diagonal. The required screen brightness of 300 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 100,000: 1 is achieved special control of the LEDs depending on the illumination of areas in the scene.This model uses an LED-panel with an edge arrangement of backlight LEDs - Edge LED. Full HD) .Input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal shaping occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
Speaker power of 16 W (2x8 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x3, MHL, USB x2. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768. The digital tuner is capable of receiving TV channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV in operating mode from the network is 220 watts.
Attention! Panel C420F16-E14-C (G11) SUPRA STV-LC42T650FL LED TV is an expensive and unreliable element.
Do not allow any impacts on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
