Technical description and composition of the PHILIPS 32PHS4012 TV, panel type and modules used. The composition of the modules.
PHILIPS LED
Model: 32PHS4012 / 12
Chassis / Version: KTS17.1E LA
Panel: LC320DXY (SJ) (A7) // K320WD82
T-CON: 6871L-5218AG
LED driver (backlight): integrated into MainBoard
PWM LED driver: 8 pin
MOSFET LED driver: TO-252
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-252
MainBoard: TP.MS3463S.PB755
IC MainBoard: CPU: MSD3463GSA, EEPROM: 25Q64, AUDIO: OB6220RVPA
Tuner: CDT-9NT372-RF01
Specifications 32PHS4012
PHILIPS 32PHS4012
General recommendations for TV LCD LED repair
Possible malfunctions
- PHILIPS 32PHS4012 does not turn on, does not respond to buttons and the remote control, the indicators on the front panel do not light or flash.
In such cases, the main power source may be faulty - the AC / DC converter of the mains voltage, which is combined with the MainBoard TP.MS3463S.PB755. It is then necessary to measure its output voltages and, in their absence, the power switches (TO-252) and the rectifier diodes of the converters should be checked for the probability of a short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in an emergency mode of a short circuit, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or the current sensor in the source of the key is often cut off.
Breakdown of Mos-Fet keys used in switching power supplies is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency setting or damper circuits, as well as in negative feedback stabilization. PWM microcircuits (PWM) PWM SOT23-6 are usually checked by replacing them with new ones, or known to be working properly.
- There is no picture, but there is sound and all other TV functions are working. The image sometimes appears for a second immediately after switching on and disappears.
The malfunction in most of such cases is found in the nodes and elements of the LED panel backlighting. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to identify an open circuit in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and a voltage of several tens of volts is required to open their junctions. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Usually, Chinese multimeters lightly light one 3-volt LED if you connect the probes to it in the forward direction (red probe to the anode, black to the cathode). For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of LED health. In the event of a malfunction of the LED, its zener diode will either be cut off or pierced in the K / Z.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the TP.MS3463S.PB755 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complicated MB (SSB) repair is possible only in the conditions of a service center with the necessary equipment. Checking or replacing elements CPU: MSD3463GSA, EEPROM: 25Q64, AUDIO: OB6220RVPA requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by the warm-up method.
If there is no reception of TV channels, but the TV is working properly from external devices, first of all, you need to check the supply voltage of the CDT-9NT372-RF01 tuner and update the software. I2C communication pulses must be monitored with an oscilloscope.
Owners and users of the PHILIPS 32PHS4012 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> PHILIPS 32PHS4012 Chassis KTS17.1E LA
The appearance of the MainBoard TP.MS3463S.PB755 is shown in the figure below:
TP.MS3463S.PB755
The main features of the PHILIPS 32PHS4012 device:
The matrix (LED panel) LC320DXY (SJ) (A7) or K320WD82 is installed.
Matrix control uses the Timing Controller (T-CON) 6871L-5218AG.
To power the backlight LEDs, a converter combined with the TP.MS3463S.PB755 main board is used, controlled by an 8 pin PWM controller. TO-252 switches are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and TO-252 type power switches.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB755 module, using CPU chips: MSD3463GSA, EEPROM: 25Q64, AUDIO: OB6220RVPA and others.
The CDT-9NT372-RF01 tuner provides reception of television programs and tuning to channels.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
AT3263 | AT3263S6 | ATC Technology | 3263 |
CR6848 | CR6848S | Chip-Rail | 848H16 |
CR6850 | CR6850S | Chip-Rail | 850xx |
CR6851 | CR6851S | Chip-Rail | 851xx |
FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
FS6830 | FS6830 | FirstSemi | |
GR8830 | GR8830CG | Grenergy | 30xx |
GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
H6849 | H6849NF | HI-SINCERITY | |
H6850 | H6850NF | HI-SINCERITY | |
HT2263 | HT2263MP | HOT-CHIP | 63xxx |
KP201 | Kiwi Instruments | ||
LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
LD7531A | LD7531AGL | Leadtrend | xxP31A |
LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
LD7551C | LD7551CGL | Leadtrend | xxP51C |
NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
PT4201 | PT4201E23F | Powtech | 4201 |
R7731 | R7731GE/PE | Richtek | 0Q= |
R7731A | R7731AGE | Richtek | IDP=xx |
SD4870 | SD4870TR | Silan Microelectronics | 4870 |
SF1530 | SF1530LGT | SiFirst | 30xxx |
SG5701 | SG5701TZ | System General | AAExx |
SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
SG6860 | SG6860TY | Fairchild | AAQxx |
SP6850 | SP6850S26RG | Sporton Lab | 850xx |
SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
SW2263 | SW2263MP | SamWin | |
UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
HT2273 | HT2273TP | HOT-CHIP | 73xxx |
LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
LD7532 | LD7532GL | Leadtrend | xxP32 |
LD7532A | LD7532AGL | Leadtrend | xxP32A |
LD7532H | LD7532HGL | Leadtrend | xxP32H |
LD7533 | LD7533GL | Leadtrend | xxP33 |
LD7536 | LD7536GL | Leadtrend | xxP36 |
LD7536R | LD7536RGL | Leadtrend | xxP36R |
LD7537R | LD7537RGL | Leadtrend | xxP37R |
LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
ME8204 | ME8204M6G | MicrOne | ME8204xx |
NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
PHILIPS 32PHS4012 TV with LCD LC320DXY, diagonal size 31.5 "(80 cm) 16: 9. The required screen brightness of 250 cd / m² is provided by LED backlighting. The LCD panel is implemented with direct LED backlighting.
The LC320DXY sensor and MainBoard TP.MS3463S.PB755 software provide high quality HD viewing at a resolution of 1366x768 pixels in 720p (HD Ready). Supported media file formats: MP3, WMA, MPEG4, HEVC (H.265), MKV, JPEG.
Speaker power 16 W (2x8 W) is provided by two speakers. Uses NICAM stereo processing system and Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, HDMI x2, MHL, USB. A headphone output is provided. The digital tuner is capable of receiving television channels in the DVB-T, DVB-T2, DVB-C, DVB-S, DVB-S2 standards.
The TV uses a power supply unit as part of the MainBoard.
Dimensions: with stand 732x492x183 mm, without stand 732x432x76 mm.
TV weight: with stand: 3.9 kg, without stand: 3.8 kg.
Attention! Panel LC320DXY (SJ) (A7) LED-TV PHILIPS 32PHS4012 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.