Technical description and composition of the BBK 40LEM-1058 TV, panel type and modules used. The composition of the modules.
BBK LED
Model: 40LEM-1058 / FT2C
Chassis / Version: CV512-U42
Panel: V400HJ6-PE1
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3352CP
MOSFET LED driver: TO-252 MDD1051
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: 65R280Q
MainBoard: CV512-U42
IC MainBoard: SPI Flash: 25Q64
Tuner: RDA5160
Specifications 40LEM-1058 / FT2C
BBK 40LEM-1058
General recommendations for TV LCD LED repair
Possible malfunctions
- TV BBK 40LEM-1058 does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lamps do not light up or flash.
A malfunction in such cases should be looked for primarily in the circuit of a switching power supply (SMPS) - a converter (AC / DC) of the mains voltage, which is combined with the MainBoard CV512-U42 in this model. It is then necessary to measure its output voltages and, if they are absent, the power switches (65R280Q) and rectifier diodes of the converters should be checked for the probability of a short circuit.
In the event of diode breakdowns in the secondary circuits, the converter can operate in an emergency mode of short circuit without output voltages, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse and / or current sensor in the source of the key usually breaks off.
The breakdown of power switches (MosFet) in switching sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency setting or damper, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM regulators (PWM) PWM SOT23-6, if they do not have visible damage to the case and an open short circuit between the pins, are usually checked by replacing.
- There is no image, the screen is black, there is sound, when the screen is illuminated outside, you can sometimes see barely noticeable outlines of the image.
In such cases, the most likely malfunction of the LED panel backlighting elements. The reason for this may be an open circuit in the LED circuit, or a problem in stabilizing their power supply.
When trying to detect a break in the LED lines, it should be borne in mind that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
READ HOW TO REPAIR THE TV LED BACKLIGHT --------------> HERE.
- The TV does not turn on, the indicator signals the standby or operating mode, or blinks.
Repair or diagnostics of the CV512-U42 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing SPI Flash: 25Q64 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by the warm-up method.
Before changing the tuner RDA5160, if there is no possibility of tuning to television channels, you should make sure that there are supply voltages, which must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange between the tuner and the processor can be monitored with an oscilloscope
Owners of the 40LEM-1058 TV are advised to contact only qualified specialists with the necessary work experience for repair! Attempts to repair yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
Revision after repair of the backlight. Information from the master.
Decrease the backlight current from 260 mA to 125 mA - removed two measuring resistors from four connected in parallel in the current sensor.
Additional MainBoard Repair
The appearance of the MainBoard CV512-U42 is shown in the figure below:
CV512-U42
Main features of the BBK 40LEM-1058 device:
Installed matrix (LED panel) V400HJ6-PE1.
To power the backlight LEDs, a converter combined with the CV512-U42 main board is used, controlled by the OB3352CP PWM controller. TO-252 MDD1051 switches are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and 65R280Q power switches.
PWM SMPS in SOT-23-6, SOT-26, TSOP-6 packages
In
the circuitry of modern switching power supplies (SMPS), PWM
controllers made in small-sized planar packages with six terminals have
gained wide popularity. The enclosure type designation can be SOT-23-6,
SOT-23-6L, SOT-26, TSOP-6, SSOT-6. The appearance and arrangement of the
pins are shown in the figure below. In this case, the code marking
LD7530A is shown on the left fragment of the picture.
Pin assignment:
1 - GND. (Common wire).
2
- FB. (FeedBack - Feedback). Input for controlling the duration of
pulses with a signal from the output voltage. Sometimes it can be
labeled COMP (input comparator).
3 - RI / RT / CT / COMP / NC -
Depending on the type of microcircuit, it can be used for a
frequency-setting RC circuit (RI / RT / CT), or for organizing
protection, as an input of a PWM trip comparator at a threshold value at
its input, specified in the document. In some types of microcircuits,
this input may not be used in any way (NC - No Connect).
4 - SENSE, otherwise CS (Current Sense) - Input from the current sensor at the source of the key.
5 - VCC - Input voltage supply and start of the microcircuit.
6 - OUT (GATE) - Output for controlling the gate (Gate) of the key.
Functionally,
these regulators work on the principle of the previously popular xx384x
PWM microcircuits, which have proven themselves well in terms of
reliability and stability.
Some difficulties often arise when
replacing or choosing an analog for such PWM regulators due to the use
of code markings in the designation of the type of microcircuits. The
situation is complicated by a large number of component manufacturers
who do not always provide documentation to the mass access, just as not
all manufacturers of finished devices supply repair service centers with
diagrams, so repairmen often have to study real circuit solutions by
installed components and wiring connections directly on the board.
In
practice, PWM microcircuits and the marking code EAxxx and Eaxxx are
often found. Official documentation for them was not found in the public
domain, but discussions on the forums and pieces of pictures from PDF
from System General, which publishes them as SG6848T and SG6848T2, have
survived. The drawing is here placed left .
For the attention of the masters, here below are PDF datasheet tables
compiled from information available on the Internet and PDF documents
for the selection of analogues types when replacing the most common
six-legged planar PWM with pinout pins: pin1 - GND, pin2 - FB (COMP),
pin4 - Sense, pin5 - Vcc, pin6 - OUT ...
Their main difference is the application and purpose of pin 3.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
SG6849 | SG684965TZ | Fairchild / ON Semi | BBxx |
SG6849 | SG6849-65T, SG6849-65TZ | System General | MBxx EBxx |
SGP400 | SGP400TZ | System General | AAKxx |
PWM controllers (PWM) with a 95-100 kOhm resistor on pin 3.
When
applying the PWM listed below, the frequency should be set with the RT
(RI) resistor from pin 3 to ground. Usually its nominal value is chosen
95-100 kOhm for a frequency of 65-100 KHz. For more details, see the
here below attached documentation. PDF files are packed in RAR.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3103A | AP3103AKTR-G1 | Diodes Incorporated | GHL |
AP8263 | AP8263E6R, A8263E6VR | AiT Semiconductor | S1xx |
AT3263 | AT3263S6 | ATC Technology | 3263 |
CR6848 | CR6848S | Chip-Rail | 848H16 |
CR6850 | CR6850S | Chip-Rail | 850xx |
CR6851 | CR6851S | Chip-Rail | 851xx |
FAN6602R | FAN6602RM6X | Fairchild / ON Semi | ACCxx |
FS6830 | FS6830 | FirstSemi | |
GR8830 | GR8830CG | Grenergy | 30xx |
GR8836 | GR8836C, GR8836CG | Grenergy | 36xx |
H6849 | H6849NF | HI-SINCERITY | |
H6850 | H6850NF | HI-SINCERITY | |
HT2263 | HT2263MP | HOT-CHIP | 63xxx |
KP201 | Kiwi Instruments | ||
LD5530 | LD5530GL LD5530R | Leadtrand | xxt30 xxt30R |
LD7531 | LD7531GL, LD7531PL | Leadtrend | xxP31 |
LD7531A | LD7531AGL | Leadtrend | xxP31A |
LD7535/A | LD7535BL, LD7535GL, LD7535ABL, LD7535AGL | Leadtrend | xxP35-xxx35A |
LD7550 | LD7550BL, LD7550IL | Leadtrend | xxP50 |
LD7550B | LD7550BBL, LD7550BIL | Leadtrend | xxP50B |
LD7551 | LD7551BL/IL | Leadtrend | xxP51 |
LD7551C | LD7551CGL | Leadtrend | xxP51C |
NX1049 | XN1049TP | Xian-Innuovo | 49xxx |
OB2262 | OB2262MP | On-Bright-Electronics | 62xx |
OB2263 | OB2263MP | On-Bright-Electronics | 63xx |
PT4201 | PT4201E23F | Powtech | 4201 |
R7731 | R7731GE/PE | Richtek | 0Q= |
R7731A | R7731AGE | Richtek | IDP=xx |
SD4870 | SD4870TR | Silan Microelectronics | 4870 |
SF1530 | SF1530LGT | SiFirst | 30xxx |
SG5701 | SG5701TZ | System General | AAExx |
SG6848 | SG6848T, SG6848T1, SG6848TZ1, SG6848T2 | Fairchild / ON Semi | AAHxx EAxxx |
SG6858 | SG6858TZ | Fairchild / ON Semi | AAIxx |
SG6859A | SG6859ATZ, SG6859ATY | Fairchild / ON Semi | AAJFxx |
SG6859 | SG6859TZ | Fairchild / ON Semi | AAJMxx |
SG6860 | SG6860TY | Fairchild | AAQxx |
SP6850 | SP6850S26RG | Sporton Lab | 850xx |
SP6853 | SP6853S26RGB, SP6853S26RG | Sporton Lab | 853xx |
SW2263 | SW2263MP | SamWin | |
UC3863/G | UC3863G-AG6-R | Unisonic Technologies Co | U863 U863G |
XN1049 | XN1049, XN1049TP | Innuovo Microelectronics | 49 xxx |
PWM controllers that use pin 3 differently.
When
using the following PWM (PWM controllers), you should pay attention to
pin 3, which can be used to organize protection - thermal or from
overvoltage of the input voltage.
The frequency can be fixed at 65kHz, or set by the value of the capacitor at pin 3.
When replacing any microcircuits with analogs, carefully study the documentation. PDF files are packed in a RAR archive.
Name | Part Number | Fabricant | Marking |
---|---|---|---|
AP3105/V/L/R | AP3105KTR-G1, AP3105VKTR-G1, AP3105LKTR-G1, AP3105RKTR-G1 | Diodes Incorporated | GHN GHO GHP GHQ |
AP3105NA/NV/NL/NR | AP3105NAKTR-G1, AP3105NVKTR-G1, AP3105NLKTR-G1, AP3105NRKTR-G1 | Diodes Incorporated | GKN GKO GKP GKQ |
AP3125A/V/L/R | AP3125AKTR-G1, AP3125VKTR-G1, AP3125LKTR-G1, AP3125RKTR-G1 | Diodes Incorporated | GLS GLU GNB GNC |
AP3125B | AP3125BKTR-G1 | Diodes Incorporated | GLV |
AP3125HA/HB | AP3125HAKTR-G1, AP3125HBKTR-G1 | Diodes Incorporated | GNP GNQ |
AP31261 | AP31261KTR-G1 | Diodes Incorporated | GPE |
AP3127/H | AP3127KTR-G1, AP3127HKTR-G1 | Diodes Incorporated | GPH GSH |
AP3301 | AP3301K6TR-G1 | Diodes Incorporated | GTC |
FAN6862 | FAN6862TY | Fairchild / ON Semi | ABDxx |
FAN6863 | FAN6863TY, FAN6863LTY, FAN6863RTY | Fairchild / ON Semi | ABRxx |
HT2273 | HT2273TP | HOT-CHIP | 73xxx |
LD7510/J | LD7510GL, LD7510JGL | Leadtrend | xxP10 xxP10J |
LD7530/A | LD7530PL, LD7530GL, LD7530APL, LD7530AGL | Leadtrend | xxP30 xxxP30A |
LD7532 | LD7532GL | Leadtrend | xxP32 |
LD7532A | LD7532AGL | Leadtrend | xxP32A |
LD7532H | LD7532HGL | Leadtrend | xxP32H |
LD7533 | LD7533GL | Leadtrend | xxP33 |
LD7536 | LD7536GL | Leadtrend | xxP36 |
LD7536R | LD7536RGL | Leadtrend | xxP36R |
LD7537R | LD7537RGL | Leadtrend | xxP37R |
LD7539C GL | LD7539C GL | Leadtrend | xxP39C |
ME8204 | ME8204M6G | MicrOne | ME8204xx |
NCP1250 | NCP1250ASN65T1G, NCP1250BSN65T1G, NCP1250ASN100T1G, NCP1250BSN100T1G | ON Semiconductor | 25xxxx |
NCP1251 | NCP1251ASN65T1G, NCP1251BSN65T1G, NCP1251ASN100T1G, NCP1251BSN100T1G | ON Semiconductor | 5xxxxx |
OB2273 | OB2273MP | On-Bright-Electronics | 73xx |
R7735 | R7735AGE, R7735HGE, R7735GGE, R7735RGE, R7735LGE | Richtek | |
UC3873/G | UC3873-AG6-R, UC3873G-AG6-R | Unisonic Technologies | U873 U873G |
LED TV BBK 40LEM-1058 / FT2C with LCD V400HJ6-PE1, diagonal size 39.5 "(100 cm) 16: 9. The required brightness of the screen of 250 cd / m2 is provided by LED backlighting. The ratio of maximum brightness to minimum ( contrast) is 3000: 1. The display technology of the model is implemented with LED backlighting.
The V400HJ6-PE1 sensor and MainBoard CV512-U42 software realize high quality HD images at a resolution of 1920x1080 pixels in 1080p (Full HD) graphics. Supported media file formats: MP3, HEVC (H.265), MKV, JPEG.
Speaker power 16 W (2x8 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x3, USB x2. A headphone output is provided. The digital tuner is capable of receiving television channels in the DVB-T, DVB-T2, DVB-C standards.
A power supply unit is used as part of the MainBoard.
Dimensions: with stand 919x583x193 mm, without stand 919x536x76 mm.
TV weight: 5.8 kg.
Attention! The V400HJ6-PE1 panel of the BBK 40LEM-1058 / FT2C LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it flows down the glass onto the cables to make the TV unrepairable.