HITACHI 50V720 / LC57 SERVICE MODE AND POWER SUPPLY CIRCUIT
LCD REAR PROJECTION TELEVISION
SERVICE MODE AND POWER SUPPLY CIRCUIT
HOW TO GET TO ADJUSTMENT MODE
Chassis adjustment mode can be access by pressing the R/C keys
Chassis adjustment mode can be access by pressing the R/C keys
MENU + MENU + 8
+ SELECT to enter adjustment mode.
For some parameters the only way to see them
is by selecting the parameter number than pressed SELECT in order to see it;
then DATA can be change if other parameter needs to change then press DOWN
ARROW key then repeat the same procedure.
Other way to access this mode is by use JIG R/C code: (9C Hex). To escape from
Adjustment Mode press “INPUT” key on Side panel or EXIT key of R/C to exit
service adjustment mode.
CHANGING DATA AND SELECTING
ADJUSTMENT CODE
When the LCD set is in adjustment mode, the
cursor UP, DOWN , LEFT ,RIGHT and
MENU keys of the remote control or front panel may be used as the adjustment
keys.
A. Use any Hitachi remote control when making an adjustment. UP, DOWN keys are used for selecting adjustment item. LEFT ,RIGHT keys are used for changing data values. MENU key is used to advance through the adjustment mode menus and pages.
A. Use any Hitachi remote control when making an adjustment. UP, DOWN keys are used for selecting adjustment item. LEFT ,RIGHT keys are used for changing data values. MENU key is used to advance through the adjustment mode menus and pages.
B. To make a selection, use the NUMBER pad on the LCD R/C ; example : select SEINE
press 69 then SELECT the DATA shown is "EB" ; if this DATA needs to
be change press the LEFT ,RIGHT keys to
modify, when finish press SELECT key to store the new DATA value. normal
condition.
C. After finishing the necessary adjustment
press the R/C EXIT key or EXIT key on the side panel. Adjustment mode is
released and LCD set returns to normal condition.
MEMORY INITIALIZE
MEMORY INITIALIZE OPERATION
NOTE: The execution of this function returns the adjustment codes to the preset values, therefore, adjustment data will be lost.
MEMORY INITIALIZE OPERATION
NOTE: The execution of this function returns the adjustment codes to the preset values, therefore, adjustment data will be lost.
Procedure
(1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (“Adjustment procedure start up”).
(2) Get to the second page of Adjust Mode by pressing remote control “Menu” key once, or with either the R/C or front panel UP, DOWN cursor keys several times.
(3) Select MEMORY INIT adjust code.
(4) Activate MEMORY INIT by pressing RIGHT cursor key for more than 3 seconds.
(5) Check the following process for initialization operation.
(8) When LCD turns ON , it will tune CH03 this is the
complete operation of Memory Initialize process.
Process of Memory Initialize operation.
1.A screen is be colored blue when MEMORY INIT start.
2.A screen is be colored green when MEMORY INIT finish normally.
3.A screen is be colored black when MEMORY INIT finish abnormally.
(6) Do not unplug from AC outlet until this operation is complete and do not perform any key operation either, after this operation each factory setting and all adjust mode data should reset to delivery settings automatically.
(7) After Memory Initialize, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data are updated.
(1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (“Adjustment procedure start up”).
(2) Get to the second page of Adjust Mode by pressing remote control “Menu” key once, or with either the R/C or front panel UP, DOWN cursor keys several times.
(3) Select MEMORY INIT adjust code.
(4) Activate MEMORY INIT by pressing RIGHT cursor key for more than 3 seconds.
(5) Check the following process for initialization operation.
(8) When LCD turns ON , it will tune CH03 this is the
complete operation of Memory Initialize process.
Process of Memory Initialize operation.
1.A screen is be colored blue when MEMORY INIT start.
2.A screen is be colored green when MEMORY INIT finish normally.
3.A screen is be colored black when MEMORY INIT finish abnormally.
(6) Do not unplug from AC outlet until this operation is complete and do not perform any key operation either, after this operation each factory setting and all adjust mode data should reset to delivery settings automatically.
(7) After Memory Initialize, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data are updated.
FACTORY RESET OPERATION
NOTE: The execution of this function returns the adjustment made by the customer , this will return all the adjustments to the original shipping conditions.
NOTE: The execution of this function returns the adjustment made by the customer , this will return all the adjustments to the original shipping conditions.
Procedure
(1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (“Adjustment procedure start up”).
(2) Get to the second page of Adjust Mode by pressing remote control “Menu” key once, or with either the R/C or front panel UP, DOWN cursor keys several times.
(3) Select FACTORY RESET adjust code.
(4) Activate FACTORY RESET by pressing RIGHT cursor key for more than 3 seconds.
(5) Check the following process for FACTORY RESET operation.
(1) Enter Adjustment mode by the method described in sub-items 1.1 and 1.2 from item 1 (“Adjustment procedure start up”).
(2) Get to the second page of Adjust Mode by pressing remote control “Menu” key once, or with either the R/C or front panel UP, DOWN cursor keys several times.
(3) Select FACTORY RESET adjust code.
(4) Activate FACTORY RESET by pressing RIGHT cursor key for more than 3 seconds.
(5) Check the following process for FACTORY RESET operation.
Process of FACTORY RESET operation.
1.A screen is be colored MAGENTA when FACTORY RESET start.
2.A screen is be colored green when FACTORY RESET finish normally.
3.A screen is be colored black when FACTORY RESET finish abnormally.
1.A screen is be colored MAGENTA when FACTORY RESET start.
2.A screen is be colored green when FACTORY RESET finish normally.
3.A screen is be colored black when FACTORY RESET finish abnormally.
(6) Do not unplug
from AC outlet until this operation is complete and do not perform any key
operation either, after this operation each factory setting and all adjust mode
data should reset to delivery settings automatically.
(7) After FACTORY RESET, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data
(7) After FACTORY RESET, it should be unplug AC cord. Unplug and plug AC cord and then all settings and data
(8) When LCD turns
ON , it will tune CH03 this is the complete operation of FACTORY RESET process are
updated.
POWER SUPPLY CIRCUIT
CLICK ON THE IMAGE TO ZOOM IN
