Lenovo YOGA TABLET 2 - AC adapter test procedure – Internal battery status check – Disassembling procedure – How Remove the rear cover – How to remove the battery pack – Laptop rpair and service
Category: Laptop Repair and Service
Contents of this article
- How to test the AC adapter
- How to remove the case
- How to remove the battery pack
Lenovo YOGA TABLET 2
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
“Checking the Computer AC Charger”
“Checking the internal battery status”
Checking the Computer AC Charger
To check the computer AC Charger, do the following:
1. Disconnect the micro-USB cable from the tablet.
2. Measure the output voltage across the connector marked B of the micro-USB cable. Refer to the following figure:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
“Checking the Computer AC Charger”
“Checking the internal battery status”
Checking the Computer AC Charger
To check the computer AC Charger, do the following:
1. Disconnect the micro-USB cable from the tablet.
2. Measure the output voltage across the connector marked B of the micro-USB cable. Refer to the following figure:
Note: The output voltage across pin 3 of the micro-B connector might be different
from the one you are servicing.
3. If the voltage is not correct, replace the micro-USB cable.
4. If the voltage is acceptable, replace the system board.
3. If the voltage is not correct, replace the micro-USB cable.
4. If the voltage is acceptable, replace the system board.
Checking the internal battery
status
To check the battery status of the tablet, do either of the following:
Approximate information about the battery status
Get the approximate status of the battery at any time by checking the battery status icon on the system bar in the upper-right corner of the screen. The shorter the green bar is, the less the battery power remains.
Accurate information about the battery status
To get the accurate information about the battery status of the tablet, do the following:
1. Open the Android Settings screen.
To open the Android Settings screen, do either of the following:
From the main Home screen, touch the Android Settings icon on
Lenovo Launch Zone. The Android Settings screen is displayed.
Pull down the application icon from the action bar and then touch Settings. The Android Settings screen is displayed.
2. Touch Battery in the Device section on the Android Settings screen.
3. The accurate percentage of the remaining battery power is shown on the screen.
To check the battery status of the tablet, do either of the following:
Approximate information about the battery status
Get the approximate status of the battery at any time by checking the battery status icon on the system bar in the upper-right corner of the screen. The shorter the green bar is, the less the battery power remains.
Accurate information about the battery status
To get the accurate information about the battery status of the tablet, do the following:
1. Open the Android Settings screen.
To open the Android Settings screen, do either of the following:
From the main Home screen, touch the Android Settings icon on
Lenovo Launch Zone. The Android Settings screen is displayed.
Pull down the application icon from the action bar and then touch Settings. The Android Settings screen is displayed.
2. Touch Battery in the Device section on the Android Settings screen.
3. The accurate percentage of the remaining battery power is shown on the screen.
DISASSEMBLING PROCEDURE
Rear cover
1. Open the hinge frame.
1. Open the hinge frame.
2. Open the card slot cover using a thin flat
blade or guitar pick.
3. Remove screws 1 on the rear cover as shown
in the figure below.
4. Separate the bottom right corner of the
rear cover from the main body of the tablet using a suction tool as shown in
the figure below.
5. Hold the tablet in one hand and use a
guitar pick to unlock the rear cover from the tablet along the joint line as
shown in the figure below.
6. Slowly remove the rear cover.
Battery pack
1. Disconnect the battery FPC from its
connector on the main board using a pair of tweezers.
2. Slowly pull out the hinge pivot using a
pair of tweezers.
3. Detach the hinge frame at the left end,
turn the hinge frame clockwise around its right end so as to steer the battery
FPC out through the supporting frame at the right end, and then remove the
hinge frame from the main body of the tablet.
4. Peel off the foil on the battery cover at
the FPC end of the hinge frame.
5. Remove screw 1 on the battery cover as
shown in the figure below.
6. Remove the battery cover as shown in the
figure below.
7. Remove the battery pack from the hinge
frame.