ONKYO TX-SR508 – TX-HTR580 - AV RECEIVER - FIRMWARE UPDATE - POWER AMPLIFIER CIRCUIT DIAGRAM

ONKYO TX-SR508 – TX-HTR580 - AV RECEIVER - FIRMWARE UPDATE - POWER AMPLIFIER CIRCUIT DIAGRAM

How to update the Firmware - Onkyo AV receiver TXSR508 - TXHTR580(B)

(HTiB:Home-Theater-in-a-Box)

HT-R580(B) in H T-S5300(B):Black model
MDC : 120V, 60Hz, Canadian model
MDD : 120V, 60Hz, USA model
MMO : 220/230-240V, 60Hz, Saudi Arabian model
MMQ : 220/230-240V, 50Hz, Hong kong model

POWER AMPLIFIER SCHEMATIC

FIRMWARE UPDATE PROCEDURE

TX-SR308/ 508 HT-R280/ 380/ 538/ 580/ HT-RC230

MAIN/DSP Update Procedure-1

FW version combination

* OSD FW cannot be updated.
*Combination of "OSD_FW and Main_FW" has limitation .
*Do not use combination except the list.

OSD menu will not appear. Before  FW Update. Check the versions of FWs

* To upgrade OSD FW version,
Replace Q8105 SPI_MEMORY "EN25Q32A-100HIP" or HDMI Board.

To check FW Versions on the monitor,
While the unit is on, hold down [DISPLAY] and the press [ON/STANDBY].
FW Versions of Main/DSP/OSD will be shown on the monitor like below.

To check FW versions on Front Display,

While the unit is on, hold down [DISPLAY] and the press [ON/STANDBY].
Main FW Version will be shown on Front Display.

e.g.  M:1.07/10413AL
1. While the unit is on, hold down [DISPLAY] and the press [ON/STANDBY].  Main FW Version will be shown on Front Display.
2. While Main FW Version is shown, press [+(TONE)].  DSP FW Version will be shown on Front Display.
* It depends on the version

e.g. D:1.02/10416a38  * It depends on the version.

OSD FW Version will not be shown on Front Display.

MAIN/DSP Update Procedure-2

[NOTE: See MAIN/DSP Update Procedure-1]
*Combination of "MAIN_FW and OSD_FW” has limitation.　　　　
*OSD FW cannot be updated.

Preparation for Update

PC （ Personal Computer） which can play back wav files and output digital audio signal at 44.1 kHz (sampling frequency)
2. Software：Given wav-formatted FW Store it in the PC in advance (PC Update) or burn a CD-R with it as a music disc (CD Update).

3. Connection: DIGITAL (OPTICAL/COAXIAL) ourput of PC/CD Player --> DIGITAL (OPTICAL-1/COAXIAL) INPUT of TX-SR308 etc.

* PC needs to be able to handle wav files and output digital audio signal at Sampling Frequency 44.1KHz.
* For wav-compatible PCs which do not output audio signal at the above specification, use a commercially-available USB-AUDIO interface unit. e.g. Onkyo-made ND-S1

Set Sampling frequency to 44.1kHz and also set Volume to Maximum.
For further information, please see Owner’s manual of your PC.

Instead of PC, CD players with DIGITAL output terminal can be used.
Note: CD players need to output digital audio signal at 44.1 kHz of sampling frequency.
Some CD players and DVD players are not suitable for update because they process audio signal to output.
Burn a CD-R as music disc.

NOTE 1
“Writing” will not be shown even more than about 15 seconds passed after starting playback, audio signal does not output at Sampling frequency:44.1kHz. Check the connection and settings and try again.  When another try results in failure again, use the other update method.
NOTE 2
DURING FW UPGRADE,DO NOT TURN OFF THE UNIT. DO NOT REMOVE ANY CONNECTIONS.  These operation will not allow FW Upgrade any more, and the whole board or IC will need replacing.

MAIN/DSP Update Procedure-3

While the unit is on, hold down [DISPLAY] and then press [ON/STANDBY].
Main FW Version will be shown on Front Display.

e.g. M:1.07/10413AL  It depends on the version.

While Main FW Version is shown, press [+(TONE)].   DSP FW Version will be shown on Front Display.

e.g.  D:1.02/10416a38 It depends on the version.

While DSP FW Version is shown, press [RETURN].

TOTAL / AUTO

> TUNING ◄► key changes “AUTO ” “COAX1” “OPT1.” 　（ ”AUTO” means “COAX1” or “OPT1” will be automatically detected.
> TUNING ▲▼ key changes “TOTAL” “MAIN” “DSP.” 　（ TOTAL = MAIN+ DSP）

When MAIN and DSP FWs are upgraded at the same time, select “TOTAL / AUTO” and press “ENTER.”
For separate upgrade, select “MAIN” or “DSP” and press “ENTER.”

S/PDIF Update..

PC upgrade: Play back the stored wav file in your PC.
CD upgrade: Play back the FW CD-R with the connected CD player. It takes about 15 minutes.

Make sure that”PCM” is shown before starting playback.
About 15 seconds later, the message will change from S/PDIF Update... to writing...
When “Writing...” will not be shown, the output music data is not correct.
Check the connection and settings.

Unplug AC cord and plug it again. Press [ON/STANDBY].

‘Clear’

Make sure that “Clear” is shown and the unit is turned into the Standby mode.
Make sure that the FW versions are the latest.