Panasonic DMP-BDT210EE how to remove the disc service mode and power supply circuit
Contents of this article
- How to remove the disc
- How to enter to special mode
- Service mode
- SMPS power supply Circuit
PANASONIC DMP-BDT210EE
SERVICE MODE AND POWER SUPPLY CIRCUIT
Taking out the Disc from Drive Unit
when the Disc cannot be ejected by OPEN/CLOSE
button When the power can be turned off.
When the power can be turned off.
1. Turn the unit off, then press and hold [OK], [Yellow] and [Blue] buttons on the remote control simultaneously for 5 seconds.
“00 RET” is displayed on the unit’s FL display.
2. Repeatedly press the right cursor button on the remote Control or Power button on the unit until “06 FTO” is displayed on the
unit's FL display.
3. Press [OK] button on the remote control or [OPEN/CLOSE] button on the unit.
When the power can not be turned off.
Press [POWER] button on the unit for over 4 seconds to turn off the power forcibly, and step 1 to 3 above.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Put the unit so that bottom can be seen.
4. Insert paper clips, etc. into the hole on the bottom of Drive Unit and slide the paper clips, etc. in the direction of the arrow to eject tray slightly.
When the power can be turned off.
1. Turn the unit off, then press and hold [OK], [Yellow] and [Blue] buttons on the remote control simultaneously for 5 seconds.
“00 RET” is displayed on the unit’s FL display.
2. Repeatedly press the right cursor button on the remote Control or Power button on the unit until “06 FTO” is displayed on the
unit's FL display.
3. Press [OK] button on the remote control or [OPEN/CLOSE] button on the unit.
When the power can not be turned off.
Press [POWER] button on the unit for over 4 seconds to turn off the power forcibly, and step 1 to 3 above.
When the Forcible Disc Eject can not be done.
1. Turn off the power and pull out AC cord.
2. Remove the Top Case.
3. Put the unit so that bottom can be seen.
4. Insert paper clips, etc. into the hole on the bottom of Drive Unit and slide the paper clips, etc. in the direction of the arrow to eject tray slightly.
5. Pull the unit upward, and push out Tray by
paper clips, etc. or minus screw driver (small).
How to enter the Special Modes using
the Multiple Pressing Function of
the Unit’s Remote Control
For pressing the multiple buttons of the remote control, this unit can be entering each of the following special modes.
After entering each mode, and then go to the menu you want to run.
the Unit’s Remote Control
For pressing the multiple buttons of the remote control, this unit can be entering each of the following special modes.
After entering each mode, and then go to the menu you want to run.
Move the menu for the each mode down mark
Press Right button on the remote control or
power button on the unit
Execute
Press OK remote cont or open/close button on the
unit
After executing the menu will automatically exit
the special mode.
How to exit from the special mode.
Press the unrelated button for the operation.
No operation for 2 minutes or more.
Press and hold power button on the unit.
Service mode
How to enter to service mode
1.Press the 5 ,9 and red button of the remote
control simultaneously for 5 second
2.Press the right cursor button on the remote
control or the power button unit
3.Press the OK button on the remote control or the
open/close button on the unit
Wait 30 seconds
Service mode will display on the fld display
How to exit the Service Mode
Press and hold the [Power] button (remote control or unit).
The Service Mode is terminated and automatically turns the unit off.
Press and hold the [Power] button (remote control or unit).
The Service Mode is terminated and automatically turns the unit off.
POWER SUPPLY CIRCUIT
