SAMSUNG LE32C53*** - LE37C53*** - LE40C53*** - LE46C53*** SERVICE MODE AND TROUBLE SHOOTING - NO VIDEO - NO AUDIO

SAMSUNG LE32C53*** - LE37C53*** - LE40C53*** - LE46C53*** SERVICE MODE AND TROUBLE SHOOTING - NO VIDEO - NO AUDIO

SAMSUNG  LE32C53*** - LE37C53*** - LE40C53*** - LE46C53*** 

SERVICE MODE AND TROUBLE SHOOTING - NO VIDEO - NO AUDIO 

Factory Mode Adjustments
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote - control
Power OFF > INFO > MENU > MUTE

How to Access Service Mode
Using the Customer Remote
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State

Option

Control

SVC

Expert

ADC/WB

Advanced

T-TDT5DEUC-XXXX T-TDT5DEUS-XXXX EDID SUCCESS CALIB : AV X COMP X PC X HDMI X Option : XXXX XXXX XXXX X T-TDTDEU-XXX SDAL-XXX RFS : P0155 T-TDT5DEUC 20XX-XX-XX TYPE : XX MODEL : XXXXX MAC Not Available FACTORY DATA VER : XXX EERC VERSION : XXX DTP-AP-COMP-XXX-XX DTP-HIIG-XXXX-X DTP-BP-XXXX DATE OF PURCHASE : XX/XX/XX

 How to enter the hidden factory mode.

a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced

Buttons operations within Service Mode

Menu	Full Menu Display/Move to Parent Menu
Direction Keys UP/DOWN	Item Selection by Moving the Cursor
Direction Keys RIGHT /LEFT	Data Increase / Decrease for the Selected Item
Source	Cycles through the active input source that are connected to the unit

White Balance –Calibration

White Ratio (Balance) Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS,
Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. (Refer to Table 1, 2)
It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 "Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment.

HDMI : Calibration at #24 Chessboard Pattern > Manual adjustment #92 pattern (720p)
COMP: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern > Manual adjustment at #92 pattern (PAL)

Servicing Information

USB Download Method
Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung  to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
1. Insert a USB drive containing the firmware upgrade into the USB port on the rear of the TV.
2. Press the MENU button to display the menu. Press the UP or DOWN  button to select "Support", then press the ENTER button.
3. Press the UP or DOWN  button to select "SW Upgrade", then press the ENTER button. The message "Scanning for USB. It may take up to 30 seconds." is displayed.
4. The message "Upgrade version XXXX to version XXXX? The system will be reset after upgrade." is displayed.
Press the LEFT or RIGHT  to select the "OK", then press the ENTER button. Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.

How To Upgrade Sub Micom With Ddc Manager

TV Sub S/W

1.Connect DDC MANAGER to the TV Set with D-SUB cable.

And Power on.
(USB type : MTI-2510 / parallel type : MTI-2059)

2.Enter the factory mode. Control - EDID - EDID ON/OFF Select ON.

3. Open the DDC tool. (Parallel type & USB type) Check the setting.

4. Load the sub micom program file.

5. Push the ‘Program’ Button. (It takes quite a bit of time. You can wait or close the DDC tool by force and open tool and load file again.)

6. Push the ‘Program’ Button again. (It takes about 100 seconds.)

7. If update completes, TV set will booting automatically. Disconnect the JIG.

Troubleshooting

1. No Power

Symptom

The LEDs on the front panel do not work when connecting the power cord.

The SMPS relay does not work when connecting the power cord.
The units appears to be dead.

Checkpoints

The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:
Check the internal cable connection status inside the unit.

Check the fuses of each part.
Check the output voltage of SMPS.
Replace the Main Board.

2. No Video (Analog PC signal)

Symptom

Audio is normal but no picture is displayed on the screen.

Checkpoints

Check the PC source
Check the Arsenal, Check the Chelsea.
This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

3. No video (HDMI1, 2, 3, 4 - Digital signal)

Symptom

Audio is normal but no picture is displayed on the screen.

Checkpoints

Check the HDMI source.

Check the HDMI switch, Check the Chelsea.
This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.

4.No Sound

Symptom

Video is normal but there is no sound..

Checkpoints

When the speaker connectors are disconnected or damaged.
When the sound processing part of the Main Board is not functioning.
Speaker defect.................