REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Saturday, 9 March 2019

SAMSUNG UE32F5070SS SOFTWARE UPDATE SERVICE MODE AND POWER SUPPLY SAMSUNG UE32F5070SS SOFTWARE UPDATE SERVICE MODE AND POWER SUPPLY

SAMSUNG UE32F5070SS SOFTWARE UPDATE SERVICE MODE AND POWER SUPPLY


SAMSUNG UE32F5070SS 

SOFTWARE UPDATE SERVICE MODE AND POWER SUPPLY 


Troubleshooting
Previous Check
1. Check the various cable connections first.
- Check to see if there is a burnt or damaged cable.
- Check to see if there is a disconnected or loose cable connection.
- Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
Main Board Assy (CN201)
13
11
9
7
5
3
1
B13V
B13V
B13VS
B13VS
GND
B5.3V
B5.3V
14
12
10
8
6
4
2
PWM_DIM
B13V
SW_INV
GND
GND
A5.3V
SW_PW

Power Board Assy (CNM803)
14
12
10
8
6
4
2
B13V
B13V
SW_INV
GND
GND
A5.3V
SW_PW
13
11
9
7
5
3
1
B13V
B13V
B13VS
B13VS
GND
B5.3V
B5.3V

* Change the 14Pin to PWM_DIM(2013 years) from B13V(2012 years)
3. Check the power in & output between IP & Main Board, Main Board & Panel, IP & Panel.
How to know it is from Main Board or T-Con when some problems happen
1. No Picture : Backlight is on, but there is no picture and LED indicator in front of TV is blinking.
- Check the LVDS Cable connection. If still problems, change the T-Con Board and then Main Board step by step.
2. Picture distortion : Enter the service mode >  Choose ‘SVC’ >  Check the ‘internal pattern.’
- Enter ‘Service Mode.’
# If you do not have Factory remote control
Power OFF > Info > MENU >  Mute > Power On
# If you have Factory remote control
INFO > Factory
3. Choose ‘SVC.’
4. Choose ‘Test pattern.’
5. Select the each pattern and then check all pattern is ok or not.
How to Check Fault Symptom
NO Power and No Video
SYMPTOM
The LEDs on The front panel do not work when connecting The power cord.
The SMPS relay does not work when connecting The power cord.
The units appears to be dead.
CHECK POINTS
The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are
improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:
# Check the internal cable connection status inside the unit.
# Check the fuses of each part.
# Check the output voltage of SMPS.
# Replace the Main Board.
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
# If you do not have Factory remote control
Power OFF > Info > MENU > MUTE > Power On
# If you have Factory remote control
INFO > Factory
3 If you don’t have Factory remote control, can’t control some menus. (Expert, Advanced menu)
How to enter the hidden factory mode.
1. Into the factory mode.
2. Move the tap to Advanced.
3. Key input : 0 + 0 + 0 + 0.
White Balance
Method of Color Calibration (PC)
1. Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port.
2. Press the Source key to switch to “PC” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “PC Calibration” menu.
6. In “PC Calibration Off” status, press the “ RIGHT ” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “PC Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1. Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port.
2. Press the Source key to switch to “Component1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “Comp Calibration” menu.
6. In “Comp Calibration Off” status, press the “RIGHT” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1. Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port.
2. Press the Source key to switch to “HDMI1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “HDMI Calibration” menu.
6. In “HDMI Calibration Off” status, press the “RIGHT” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “HDMI Calibration” status from Failure to Success.
Method of Color Calibration (AV)
1. Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port.
2. Press the Source key to switch to “AV1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “AV Calibration” menu.
6. In “AV Calibration Off” status, press the “RIGHT” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “AV Calibration” status from Failure to Success.
White Ratio (Balance) Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS,
Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. It varies with Panel’s size and Specification.
• Equipment : CS-210
• Pattern: MIK K-7256 #92 “Flat W/B Pattern" as standard
• Altenate Equipmet : CA200& anyone Master supported
pattern#92(refer to right photo)
• Use other Equipment only after comparing the result
with that of the Master equipment.
• Set Aging time : 60 min
Calibration and Manual setting for WB adjustment
• HDMI : Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
• COMP: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
• CVBS: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (NTSC)
Software Upgrade
Software Upgrade can be performed by downloading the. latest firmware from samsung.com to a USB memory device.
# Current Version - The software already installed in the TV.
Software is represented as ‘Year/Month/Day_Version’.
How to Check the Software Version
Use the Main Menu
1. Click the "MENU" key in remote controller.
2. Select "Support" menu.
3. Locate the menu cursor "Software Upgrade" menu.
4. Click the "INFO" key.
- Check the Main SW and Micom version.
How to Upgade Software and Micom
Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV. Please be careful not
to disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on
automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are complete
(the new version will have a higher number than the older version). When software is upgraded, video and audio
settings you have made will return to their default (factory) settings. We recommend you write down your settings before
beginning firmware update. After update is completed, restore your previous settings.
Main Software Upgrade
1. Store the sw program named "T-MST13DEUC" in USB memory stick
- Connect the USB.
2. Click the "MENU" key in Remote Controler.
3. Select "Support" menu.
Locate the menu cursor "Software Upgrade" menu.
4. Locate the menu cursor "Update now" menu.
5. Click the "ENTER" key.
6. Click the "ENTER" key.
- Wait for upgrade complete.
- Check the Software Version.

POWER SUPPLY 
BN44-00607A
CLICK ON THE IMAGE TO ZOOM IN
Posted By: FRANK at 04:33
TAG: , , , ,