REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Saturday, 9 March 2019

SAMSUNG UE40H7000AL - UE46H7000AL - UE55H7000AL - UE60H7000AL SERVICE MODE ADJUSTMENTS AND POWER SUPPLY

SAMSUNG UE40H7000AL - UE46H7000AL - UE55H7000AL - UE60H7000AL SERVICE MODE ADJUSTMENTS AND POWER SUPPLY


SAMSUNG UE40H7000AL - UE46H7000AL - UE55H7000AL - UE60H7000AL

 LED TV 


SERVICE MODE ADJUSTMENTS AND POWER SUPPLY 


Troubleshooting
Check list for initial operation
 AC Power Cord connected to the TV and the wall receptacle.
 Standby Power/IR Indicator LED is turned On.
 If Power/IR Indicator is not on check 10p power cable is connected and for correct Standby Voltage from SMPS to Main. Also check Jog Function Cable.
 Power turned On with Jog Function or Remote.
 Power on command from main Board to SMPS.
 Power/IR Indicator Flashes.
 Panel Back Lights are turned On.
 If no Backlights, unplug AC Power Cord, unplug 10 pin connector to SMPS, plug in AC Power Cord, Back light should come on. Check Main Board   operation for error.
 Power/IR Indicator goes off.
Picture or banner is displayed.
# If nothing is displayed, check the LVDS cable
DC Output Connector (40 inches)
CNM803 : YEONHO (SMAW200-H18S5K)
PIN
Signal
PIN
Signal
1
PWM_DIM3
2
PWM_DIM_2
3
GND
4
PWM_DIM_1
5
A13
6
OD_ON/OFF
7
A13
8
ON_LEVEL
9
A13
10
BLU_ON/OFF
11
A13
12
OWER_ON/OFF
13
A13
14
GND
15
GND
16
GND
17
N.C
18
N.C

DC Output Connector (46/55/60 inches)

CNL801A
CNL802B
UJU (FF200-L10T-C26)
PIN
Signal
PIN
Signal
1
NC
1
NC
2
NC
2
R1+
3
L4+
3
R1-
4
L4-
4
R2+
5
L3+
5
R2-
6
L3-
6
R3+
7
L2+
7
R3-
8
L2-
8
R2+
9
L1+
9
R2-
10
L1-
10
NC






CNM803 : YEONHO (SMAW200-H22S5)
Signal
PIN
PIN
Signal
Vamp
21
22
GND
Vamp
19
20
Vamp
GND
17
18
GND
A13V
15
16
GND
A13V
13
14
Power On/Off
A13V
11
12
BLU On/Off
A13V
9
10
OD Level
A13V
7
8
OD On/Off
GND
5
6
PWM_DIM 1
PWM_DIM 3
3
4
PWM_DIM 2
-
1
2
PWM_DIM 4

How to check inner pattern?
1. Move to Factory mode.
Power OFF > INFO > MENU > MUTE > Power On
2. Move to ‘Service Mode.’
3. Move to ‘Test pattern’.
Fault Symptom
No Power
Symptom
The LEDs on The front panel do not work when connecting The power cord.
The SMPS relay does not work when connecting The power cord.
The units appears to be dead.
Checkpoints
The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:
Check the internal cable connection status inside the unit.
Check the fuses of each part.
Check the output voltage of SMPS.
Replace the Main Board.
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
# If you do not have Factory remote control
Power OFF > INFO > MENU > MUTE > Power On
# If you have Factory remote control
INFO >  Factory
# If you don’t have Factory remote control, can’t control some menus. (Expert, Advanced menu)
Method of Color Calibration (AV)
1. Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port.
2. Press the Source key to switch to “AV1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “AV Calibration” menu.
6. In “AV Calibration Off” status, press the “ >  ” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “AV Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1. Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port.
2. Press the Source key to switch to “Component1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “Comp Calibration” menu.
6. In “Comp Calibration Off” status, press the “ > ” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (PC)
1. Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port.
2. Press the Source key to switch to “PC” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “PC Calibration” menu.
6. In “PC Calibration Off” status, press the “ > ” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “PC Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1. Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port.
2. Press the Source key to switch to “HDMI1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “HDMI Calibration” menu.
6. In “HDMI Calibration Off” status, press the “> ” key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “HDMI Calibration” status from Failure to Success.
POWER SUPPLY BOARD 
PART NUMBER SAMSUNG BN44-00269B
CLICK ON THE IMAGE TO ZOOM IN
Posted By: FRANK at 04:37
TAG: , , ,