SANYO DP42849 SERVICE MODE AND POWER SUPPLY PART NUMBER
SANYO DP42849
SERVICE MODE AND POWER SUPPLY PART NUMBER
How to Enter the Service Menu
1.Turn off the receiver and disconnect the AC power
supply.
2. While pressing the Volume (–) button on the television, reconnect the AC power supply. The Service Menu will now appear. The remote can now be used to make adjustments.
1.Turn off the receiver and disconnect the AC power
supply.
2. While pressing the Volume (–) button on the television, reconnect the AC power supply. The Service Menu will now appear. The remote can now be used to make adjustments.
POSITIONS OF THE KEY ON TV
How to make adjustments
1. Press the Cursor UP and DOWN key to select the desired service menu item you want to adjust. See page 4 for the On-screen Service Menu.
2. Use the Cursor LEFT or RIGHT key to adjust the data The or key will increase or decrease the data sequentially.
1. Press the Cursor UP and DOWN key to select the desired service menu item you want to adjust. See page 4 for the On-screen Service Menu.
2. Use the Cursor LEFT or RIGHT key to adjust the data The or key will increase or decrease the data sequentially.
How to exit service menu
Press the MENU key to turn off the Service Menu display.
ON-SCREEN SERVICE MENU
When IC801 (EEPROM) is replaced, check the bus data to confirm they are the same as below
When IC801 (EEPROM) is replaced, check the bus data to confirm they are the same as below
No.
|
Title
|
Initial Data
|
Note
|
1A0
|
MUTE
|
A0h
|
Audio
mute at Power ON
|
086
|
VOL
|
30h
|
Volume
setup inspection
|
087
|
OP1
|
00h
|
Option
1 Data (HDMI)
|
088
|
OP2
|
24h
|
Option
2 Data (Display Panel)
|
101
|
1R00
|
00h
|
ROM
Correction Data
|
102
|
1R01
|
00h
|
ROM
Correction Data
|
197
|
2R47
|
00h
|
ROM
Correction Data
|
198
|
2R48
|
00h
|
ROM
Correction Data
|
PROGRAM CODES
The microprocessor used in this model is a multi-purpose type and is used in several different models. To ensure proper operation and the correct features for your particular model, the program codes must be correct.
The microprocessor used in this model is a multi-purpose type and is used in several different models. To ensure proper operation and the correct features for your particular model, the program codes must be correct.
Note 1. Option Data 1 (NO. 087 OP1)
should be hexadecimal 00. See 087 above. If this
program code is wrong the TV will not operate properly.
Note 2. Option Data 2 (NO. 088 OP2)
should be hexadecimal 24. See 088 above. If this
program code is wrong the TV will not operate properly.
POWER FAILURE CIRCUIT
CPU (IC800) is programmed so the set will go to
standby mode when there is circuit failure as described below.
This unit is equipped with a Power Failure Detector function included in the CPU which checks for an abnormal condition in the chassis power supplies. If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the unit off in 1.5 seconds to prevent further damage:
1. Failure within the power supply circuits.
2. A short circuit in the load side from the supply.
Power Failure: Detected voltage failure for circuit. (Connected to IC800 pin 48 and pin 23.)
(Normal: High; Failure: Low)
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the power within three seconds.
This unit is equipped with a Power Failure Detector function included in the CPU which checks for an abnormal condition in the chassis power supplies. If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the unit off in 1.5 seconds to prevent further damage:
1. Failure within the power supply circuits.
2. A short circuit in the load side from the supply.
Power Failure: Detected voltage failure for circuit. (Connected to IC800 pin 48 and pin 23.)
(Normal: High; Failure: Low)
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the power within three seconds.
Check the following
if the unit is turned off by the power failure detector.
1. Disconnect the AC power cord (120V AC line) for a short time.
2. Connect a DC Voltmeter to the circuits shown below.
3. Press the Power key and check for the proper voltage supplies.
4. If any of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits shown below.
Note: If power failure is detected 3 times in 15 minutes, the set will enter the standby mode and cannot be switched On.To reset the operating programs of the CPU it is necessary to disconnect the AC cord for a short time.
1. Disconnect the AC power cord (120V AC line) for a short time.
2. Connect a DC Voltmeter to the circuits shown below.
3. Press the Power key and check for the proper voltage supplies.
4. If any of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits shown below.
Note: If power failure is detected 3 times in 15 minutes, the set will enter the standby mode and cannot be switched On.To reset the operating programs of the CPU it is necessary to disconnect the AC cord for a short time.
No:- 1AV4U20C39200
