REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Friday, 8 March 2019

SONY HCD-DZ530 - DZ630 COLD RESET ERROR CODES AND POWER SUPPLY CIRCUIT

SONY HCD-DZ530 - DZ630 COLD RESET ERROR CODES AND POWER SUPPLY CIRCUIT

SONY HCD-DZ530 - DZ630 

COLD RESET ERROR CODES AND POWER SUPPLY CIRCUIT  

SERVICING NOTE
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.
Setting Procedure :
1. Press the POWER button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the STOP button and the A button simultaneously for five seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the STOP button and the A button simultaneously for five seconds again.
2. The message “UNLOCKED” is displayed and the tray is unlocked.
Note: When “LOCKED” is displayed, the tray lock is not released by turning power on/off with the POWER  button.
Attention when transported
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the POWER button to turn the set on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons PLAY and POWER simultaneously.
4. After a message “MECHA LOCK” is displayed on the fluorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the POWER button to turn the set on.
How to open the disc table when power switch turns off
Insert a tapering driver into the aperture of the unit bottom, and slide it in the direction of the arrow.
Peel off the seal and so the lever is moved
in the direction of the arrow with the thin rod.

Discharge the charged electricity in capacitors to prevent electric shock as follows
When disassembling the machine, be sure to discharge the charged electricity in the following capacitors. Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
POWER board
C903: 390 V ,C932, C933, C934, CN904: 30 V
MAIN board
CN3002: 30 V

TEST MODE
Cold Reset
 The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
Procedure:
1. Press the POWER  button to turn the power on.
2. Press three buttons STOP , EJECT and POWER simultaneously.
3. When this button is operated, display as “COLD RESET” for
a while and all of the settings are reset.
Panel Test Mode
This mode is used to check the software version, FL and KEY.
Display Test Mode
Procedure:
1. Press the POWER  button to turn the power on.
2. Press three buttons PAUSE , PREVIOUS  and EJECT  simultaneously.
3. When the display test mode is activated, all segments are turned on.
4. To exit from this mode, press three buttons X , . and A
simultaneously.
Key Test Mode
Procedure:
1. When the display test mode is activated, press the PLAY button, to select the key test mode.
2. To enter the KEY test mode, the fluorescent indicator displays “K0 V0”. Each time an another button is pressed, “KEY” value increases. However, once a button is pressed, it is no longer taken into account. When all keys are pressed correctly, “K8 V0” is displayed.
3. When the VOLUME control is turned in the direction of (+), “V0” is changed to “V1”, then ... “V9”.
When the VOLUME control is turned in the direction of (–), “V0” is changed to “V9”, then ... “V1”.
4. To exit from this mode, press three buttons PAUSE , PREVIOUS and EJECT simultaneously.
Disc Tray Lock
The disc tray lock function for the antitheft of an demonstration disc in the store is equipped.
Setting Procedure :
1. Press the POWER button to turn the power on.
2. Press the FUNCTION button to set DVD function.
3. Insert a disc.
4. Press the STOP button and the EJECT button simultaneously for five seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the STOP button and the EJECT button simultaneously for five seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note: When “LOCKED” is displayed, the tray lock is not released by turning power on/off with the POWER button.
DVD Ship Mode
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the POWER button to turn the power on.
2. Press the FUNCTION button to set the function “DVD”.
3. Remove all discs, and then press two buttons PLAY and POWER simultaneously.
4. After a message “MECHA LOCK” is displayed on the
fluorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the POWER button to turn the set on.
Product Out
This mode moves the optical pick-up to the position durable to vibration and clears all data including preset data stored in the RAM to initial conditions. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the POWER button to turn the power on.
2. Press the FUNCTION button to set the function “DVD”.
3. Remove all discs, and then press three buttons NEXT , EJECT and  POWER simultaneously.
4. After the “STANDBY” blinking display finishes, the message “MECHA LOCK” is displayed on the fluorescent indicator tube disconnect the AC power plug, then the ship mode is set.
Demo Play Out
It is a mode to release the demonstration reproduct by the dedicated demonstration disc.
Setting Procedure:
1. Press the POWER button to turn the power on.
2. Press the FUNCTION button to set the function “DVD”.
3. During playback the DEMO Disc, press the STOP and PLAY buttons for five seconds simultaneously.
4. The message “DEMO OFF” is displayed, a mode to reproduct the demonstration is released.
Volume Test
Procedure:
1. Press the POWER button to turn the power on.
2. Press three buttons PREVIOUS , PLAY, NEXT   simultaneously.
3. The message “VOLUME MIN” is displayed.
4. When the VOLUME control is turned in the direction of (+), the message “VOLUME MAX” is displayed.
5. When the VOLUME control is turned in the direction of (–), the message “VOLUME MIN” is displayed.
6. To exit from this mode, press the ?/1 button to turn the set off, the message “COLD RESET” is displayed.
Automatic Acoustic Field Calibration Microphone Test Mode
Procedure:
1. Press the POWER button to turn the power on.
2. Press the FUNCTION button to set the function “DVD”.
3. Insert ECM-AC2 supplied as an accessory into the AUDIO IN/MIC 1/A.CAL MIC jack.
4. While pressing the PAUSE and EJECT buttons simultaneously, turn the VOLUME control in the direction of (+) .
5. Confirm that the following are shown on the display panel.
1 The JACK inserted/non-inserted detection display and the STEREO/MONO detection display.
2 Presence of DIGITAL voice input to the microcomputer. (OK: input, NG: no input)
3 The value of the MIC input to the microcomputer. (shown
“0 – 255” (Changes in real time))
How To Enter Test Mode
While pressing the STOP and EJECT buttons simultaneously, turn VOLUME control in the direction of (+) with the DVD player in
power on.
The Test Mode starts, displayed “SERVICE IN” on this model display then the menu shown below will be displayed on the TV screen.
ERROR CODES AND DESCRIPTION 
ERROR CODE
Meaning of error code
01:
Communication error (No reply from syscon)
02:
Syscon hung up
03:
Power OFF request when syscon hung up
19:
Thermal shutdown
24:
MoveSledHome error
25:
Mechanical move error (5 Changer)
26:
Mechanical move stack error
30:
DC motor adjustment error
31:
DPD offset adjustment error
32:
TE balance adjustment error
33:
TE sensor adjustment error
34:
TE loop gain adjustment error
35:
FE loop gain adjustment error
36:
Bad jitter after adjustment
40:
Focus NG
42:
Focus layer jump NG
POWER SUPPLY CIRCUIT 
USING STR-F6168 - STR-VI53
CLICK ON THE IMAGE TO ZOOM IN
Posted By: FRANK at 02:06
TAG: , , , ,