
SAMSUNG
Model: LE32B650
Chassis / Version: N68A
Panel: LTF320HA09
T-CON: 320HAC2LV0.4
Inverter (backlight): integrated into PSU
PWM Inverter: SEM2006
MOSFET Inverter: 4N50
Power Supply (PSU): BN44-00261A
PWM Power: FAN7530 (PFC), STR-W6252
MOSFET Power: 6N60
MainBoard: BN41-01165A
IC MainBoard: CPU: SEMS12, DRAM: K4T511630G-HCE7, SPI Flash: 25L6405DMI-12G, NTP3200, MX25L6445D, WT61P8
Tuner: BN40-00137A
Specifications LE32B650
SAMSUNG LE32B650
General repair guidelines for TV LCD
Possible malfunctions
- The SAMSUNG LE32B650 TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
With such manifestations, a malfunction is most likely to be detected in the BN44-00261A power module. It is then necessary to measure its output voltages and, if they are absent, you should check the power switches (6N60) and the rectifier diodes of the converters for the probability of a short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) FAN7530 (PFC), STR-W6252, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously working ones.
- There is no image, there is sound, it reacts to the remote control, channels are switched. In some cases, the image appears when you turn on and immediately disappears.
These manifestations can be triggered by a power supply module, or by inverter defects, as well as a distortion of the currents in the lamps due to their uneven wear. After checking all the electrolytic capacitors of the filters that are involved in powering the inverter, you should ring in its converter power keys for breakdown and the secondary windings of transformers for an open.
If in diagnosing a malfunction, it is necessary to disable the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during operations, and after their completion, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-01165A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). When repairing an MB board, you need to check its CPU components: SEMS12, DRAM: K4T511630G-HCE7, SPI Flash: 25L6405DMI-12G, NTP3200, MX25L6445D, WT61P8. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00137A. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Attention! Users and owners of LE32B650 TVs who do not have the appropriate qualifications, knowledge and experience are strongly advised against self-repair attempts in order to avoid negative consequences that could lead to complete non-repairability of the device.

BN41-01165A
BN41-01165A can be used in TVs:
SAMSUNG LE32B450C4 LE32B450C4W (Panel LTF320AP06), SAMSUNG LE37B530P7 LE37B530P7W (Panel AX094F040E), SAMSUNG LE40B530P7 LE40B530P7W (Panel LTF400HA08), SAMSUNG LE46B530P7 LE46B530P7W (Panel V460H1-L06 RevC1), SAMSUNG LE32B530 LE32B530P7W (Panel LTF320HA09), SAMSUNG LE40B531 LE40B531P7W (Panel LTF400HA08) .
The appearance of the power supply
Main features of the SAMSUNG LE32B650 device:
Installed matrix (LCD-panel) LTF320HA09.
The matrix control uses the Timing Controller (T-CON) 320HAC2LV0.4.
To power the backlight, a converter is used, combined with a power supply, controlled by a PWM controller SEM2006. As power elements of the inverter, keys of type 4N50 are used.
The necessary supply voltages for all nodes of the SAMSUNG LE32B650 TV are generated by the BN44-00261A power module or its analogs using FAN7530 (PFC), STR-W6252 microchips and 6N60 type power switches.
MainBoard - the main board (motherboard) is a BN41-01165A module, using CPU chips: SEMS12, DRAM: K4T511630G-HCE7, SPI Flash: 25L6405DMI-12G, NTP3200, MX25L6445D, WT61P8 and others.
The tuner BN40-00137A provides the reception of television programs and tuning to channels.
