Technical description and composition of the SAMSUNG 32D6510 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: 32D6510 32D6510WS
Chassis / Version: CN01
Panel: LD320CSC-C2
T-CON: V460HK1-C01
LED driver (backlight): integrated into PSU
PWM LED driver: SLC3011M
MOSFET LED driver: MDF12N50
Power Supply (PSU): BN44-00458B PD46A1D_BHS
PWM Power: STR-A6052M, SPC7011F, FSFR1800XSL
MOSFET Power: MDF10N60G (PFC)
MainBoard: BN41-01587E
IC MainBoard: SDP1001, SDP1005, SDP94, SIL9489ACTU, K4B2G1646C-HCH9, EPM240T100C4N
Tuner: BN40-00217A DNSS243VH142A
Technical Specifications UE32D6510
SAMSUNG 32D6510
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG 32D6510 TV does not turn on. There is no reaction to the remote control and to the control buttons from the front panel. Indicator lights do not light or flash.
In such cases, the BN44-00458B power supply is usually faulty. It is necessary to measure the secondary output voltage, and in case of their absence, check the health of the power switches (MDF10N60G (PFC)) of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may also be PWM (PWM) STR-A6052M, SPC7011F, FSFR1800XSL. It is checked only by replacement with a known good one.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-01587E motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - SDP1001, SDP1005, SDP94, SIL9489ACTU, K4B2G1646C-HCH9, EPM240T100C4N with new or obviously working ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
If the tuner BN40-00217A DNSS243VH142A is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
For 32D6510 TV owners, we recommend that you contact qualified specialists with the necessary work experience for repairs! Attempts to repair it yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
The appearance of the MainBoard BN41-01587E is shown in the figure below:
BN41-01587E
BN41-01587E can be used in TVs:
SAMSUNG UE40D6510 UE40D6510WS (Panel LD400CSC-C2), SAMSUNG UE55D6100SW (Panel LTJ550HW04-L), SAMSUNG UE46D6530WS UE46D6530 (Panel LTJ460HW01-V), SAMSUNG 32D6510 32D6510WS (Panel LD320CSC-C2), SAMSUNG UE40D6530 UE40D6530WS (Panel LTJ400HV01-V), SAMSUNG UE46D6510WS UE46D6510 (Panel LTJ460HW02-L), SAMSUNG UE32D6510WS UE32D6510 (Panel LD320CSC-C2), SAMSUNG UE40D6500 UE40D6500VS (Panel LTJ400HV01-J).
The appearance of the power supply
Main features of the SAMSUNG 32D6510 device:
Installed matrix (LED panel) LD320CSC-C2.
The matrix control uses the Timing Controller (T-CON) V460HK1-C01.
To power the backlight LEDs, a converter is used, combined with the power supply, controlled by the PLC controller SLC3011M. As power elements of the LED driver, keys of the MDF12N50 type are used.
The necessary supply voltages for all nodes of the SAMSUNG 32D6510 TV are generated by the BN44-00458B power supply module or its analogs using the STR-A6052M, SPC7011F, FSFR1800XSL microcircuits and MDF10N60G (PFC) type power switches.
MainBoard - the main board (motherboard) is a module BN41-01587E, using microchips SDP1001, SDP1005, SDP94, SIL9489ACTU, K4B2G1646C-HCH9, EPM240T100C4N and others.
The tuner BN40-00217A DNSS243VH142A provides the reception of television programs and tuning to channels.
