Technical description and composition of the SAMSUNG UE32J5200AK TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32J5200AK
Chassis / Version: Ver: TS01
Panel: CY-JJ032BGLV1V
LED backlight: V5DN-320SM1-R2 (15.05.13)
T-CON: BN41-02111A
LED driver (backlight): with integrated MainBoard
PWM LED driver: BD9397EFV
Power Supply (PSU): Adapter
MainBoard: BN41-02360B BN94-08318B
IC MainBoard: K4B2G1646Q, TAS5747
Tuner: BN40-00316A
Control: IR: BN41-02398A, Wi-Fi: WDF710Q BN59-01196C
Technical Specifications UE32J5200AK
SAMSUNG UE32J5200AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE32J5200AK does not turn on. There are no signs of operability. The indicators on the front panel do not shine and do not blink, and the remote control and control buttons do not respond.
In the vast majority of such cases, a malfunction is detected in the Adapter power module.
This TV model is equipped with an external adapter type power supply, which the owner can purchase on his own, and repairing it may not always be advisable, however, sometimes it makes sense to open it and eliminate simple typical defects typical of IPS. It is necessary to measure the secondary output voltage, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, there is sound, it responds to the remote. Or the image may appear for a second when turned on and immediately disappears.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02360B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements K4B2G1646Q, TAS5747. BGA chip malfunctions are usually easy to detect by warming up.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00316A. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Owners and users of the SAMSUNG UE32J5200AK TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
The appearance of the MainBoard BN41-02360B is shown in the figure below:BN41-02360B
BN41-02360B can be used in TVs:
SAMSUNG UE32J5200AK (Panel CY-JJ032BGLV1V), SAMSUNG UE32J5205AK UE32J5205 (Panel CY-JJ032BGLV6V), SAMSUNG UE32J4500 UE32J4500AK (Panel CY-JJ032AGHVEV).
Main features of the SAMSUNG UE32J5200AK device:
Installed matrix (LED panel) CY-JJ032BGLV1V.
The matrix control uses the Timing Controller (T-CON) BN41-02111A.
To power the backlight LEDs, a converter is used, combined with the main board BN41-02360B, controlled by the BD9397EFV PWM controller.
To power all internal components of the SAMSUNG UE32J5200AK TV, an external adapter type source is used.
MainBoard - the main board (motherboard) is a BN41-02360B module, using K4B2G1646Q, TAS5747 and others.
The tuner BN40-00316A provides the reception of television programs and tuning to channels.
