Technical description and composition of the LG 32LF560V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 32LF560V
Chassis / Version: LC55H / LD55T / LB55T / LJ55T
Panel: NC320DUN-VBBP3
LED backlight: 6916L-2223A, 6916L-224A
T-CON: HV320FHB-N00
LED driver (backlight): integrated into PSU
PWM LED driver: BD559
MOSFET LED driver: MDD5N40
Power Supply (PSU): LGP32D-15CH1
PWM Power: SSC3S111
MOSFET Power: MDF11N65B
MainBoard: EAX66203805 (1.2)
IC MainBoard: CPU: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256
Tuner: TDJM-G301D
Control: IR: EBR78480602
Specifications 32LF560V
LG 32LF560V
General repair guidelines for TV LCD LED
Possible manifestations of defects
- LG 32LF560V TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
Most likely in this case, the main switching power supply (IIP) LGP32D-15CH1 is faulty. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches (MDF11N65B) and rectifier diodes for a possible partial or complete breakdown.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers SSC3S111, in the absence of visible damage or obvious short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
As a rule, in such cases there is no display backlight. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the EAX66203805 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256 and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
Before replacing the TDJM-G301D tuner, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
For 32LF560V TV owners, we recommend that you contact qualified personnel with the necessary work experience for repairs! Self-repair attempts without the appropriate knowledge and skills can lead to irreversible negative consequences!
Service manual and schematic diagram -------------------> LG 32LF560U Chassis LD55T.
MODS: 32LF56**, 32LF56**-Z*
The appearance of the MainBoard EAX66203805 is shown in the figure below:EAX66203805
EAX66203805 can be used in TVs:
LG 32LF564U (Panel LC320DXE (MG)(A3)), LG 42LF550V (Panel LC420DUE (MG)(A6)), LG 32LF560U ZB (Panel NC320DXN VSBP5 ), LG 42LF560V (Panel LC420DUE (MG)(A3)), LG 32LF562V (Panel NC320DUN-VBBP3 (EAJ63171201)), LG 32LF564V (Panel NC320DUN VBBP3), LG 32LF560V (Panel NC320DUN-VBBP3), LG 49LF620V 49LF620V-ZB (Panel LC490DUE (MG)(P2)), LG 42LF551C (Panel LC420DUE-MGA6).
The appearance of the power supply
Main features of the device LG 32LF560V:
Installed matrix (LED-panel) NC320DUN-VBBP3.
The matrix control uses the Timing Controller (T-CON) HV320FHB-N00.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a BD559 PWM controller. As power elements of the LED driver, keys of the MDD5N40 type are used.
The necessary supply voltages for all nodes of the LG 32LF560V TV are generated by the LGP32D-15CH1 power module or its analogs using SSC3S111 microcircuits and power switches of the MDF11N65B type.
MainBoard - the main board (motherboard) is an EAX66203805 module, using CPU chips: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256 and others.
The TDJM-G301D tuner provides TV reception and channel tuning.
