Technical description and composition of the LG 32LF562V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 32LF562V
Chassis / Version: LD55T
Panel: NC320DUN-VBBP3 (EAJ63171201)
LED backlight: HC320DXN-ABHR2 LATWT326RXLZK A
T-CON: HV320FHB-N00
LED driver (backlight): integrated into PSU
Power Supply (PSU): EAX66171501 (2.1) REV3.0 LGP32D-15CH1
PWM Power: SSC3S111
MOSFET Power: MDF11N65B
MainBoard: EAX66203805 (1.2)
IC MainBoard: CPU: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256
Tuner: TDJM-G301D
Control: IR: EBR78480602
Specifications 32LF562V
LG 32LF562V
General repair guidelines for TV LCD LED
Possible manifestations of defects
- LG 32LF562V does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
With such manifestations, the EAX66171501 power module usually fails. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches (MDF11N65B) and rectifier diodes of converters for possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key are most often cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) SSC3S111, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the EAX66203805 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sometimes they require verification or replacement (if necessary) of the MainBoard - CPU: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
If a TDJM-G301D tuner is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary supply voltage levels and data exchange pulses with the processor via the I2C bus at the corresponding tuner pins.
For 32LF562V TV owners, we recommend that you contact qualified personnel with the necessary work experience for repairs! Self-repair attempts without the appropriate knowledge and skills can lead to irreversible negative consequences!
Service manual and schematic diagram LG 32LF562V Chassis LD55T. 32LF56**, 32LF56**-Z*
You can reduce the backlight current in TVs with LGP32D-15CH1 power supplies (EAX66171501) if you increase the resistance of the current sensor - the R816 resistor from 2.4 Ohm to 3 Ohm. Then the backlight current will proportionally decrease from 250 mA to 200 mA. If you install a 3.3 Ohm resistor, the current will decrease to 180 mA.
More details on this page
The appearance of the MainBoard EAX66203805 is shown in the figure below:EAX66203805
EAX66203805 can be used in TVs:
LG 32LF564U (Panel LC320DXE (MG)(A3)), LG 42LF550V (Panel LC420DUE (MG)(A6)), LG 32LF560U ZB (Panel NC320DXN VSBP5 ), LG 42LF560V (Panel LC420DUE (MG)(A3)), LG 32LF562V (Panel NC320DUN-VBBP3 (EAJ63171201)), LG 32LF564V (Panel NC320DUN VBBP3), LG 32LF560V (Panel NC320DUN-VBBP3), LG 49LF620V 49LF620V-ZB (Panel LC490DUE (MG)(P2)), LG 42LF551C (Panel LC420DUE-MGA6).
The appearance of the power supply
Main features of the device LG 32LF562V:
Installed matrix (LED-panel) NC320DUN-VBBP3 (EAJ63171201).
The matrix control uses the Timing Controller (T-CON) HV320FHB-N00.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the LG 32LF562V TV are generated by the EAX66171501 power supply module or its analogs using SSC3S111 microcircuits and power switches of the MDF11N65B type.
MainBoard - the main board (motherboard) is an EAX66203805 module, using CPU chips: LGE2134; NAND Flash: TC58NVG0S3HTA00; SPI Flash: MX25L8035EM2I; EEPROM: 24C256 and others.
The TDJM-G301D tuner provides TV reception and channel tuning
