Technical description and composition of the PHILIPS 42PFL6678S TV, panel type and applicable modules. The composition of the modules.PHILIPS LED
Model: 42PFL6678S / 12
Chassis / Version: QFU1.2E LA
Panel: LC420EUF (PF) (F1)
LED backlight: 6920L-0001C, 6922L-0072A
T-CON: 6870C-0450A
LED driver (backlight): integrated into PSU
PWM LED driver: BD9479FV
Power Supply (PSU): FSP140-4FS01
PWM Power: FSB117H (Standby), FAN7930 (PFC), SSC9522S (PWM)
MainBoard: 310431366185 3104 303 54945 3104 313 66185
IC MainBoard: FUSION120, H5TQ2G63BFR, H5TQ2G83BFR, SPI Flash: 25P10VP.
Tuner: SUT-RE214AN H 3D129G
Specifications 42PFL6678S
PHILIPS 42PFL6678S
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The PHILIPS 42PFL6678S TV does not turn on at all. The control lights do not light or flash. The TV on the remote control and the control panel buttons do not respond.
Most likely in this case, the main switching power supply (MPS) FSP140-4FS01 is faulty. It is necessary to measure its output supply voltage, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for the probability of breakdown in PN semiconductor junctions.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers FSB117H (Standby), FAN7930 (PFC), SSC9522S (PWM), in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
In most of these cases, a malfunction is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, it does not respond to the remote control.
Repair or diagnostics of the 310431366185 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - FUSION120, H5TQ2G63BFR, H5TQ2G83BFR. Defective components should be replaced.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltages at the terminals of the SUT-RE214AN tuner. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Attention to users! Self-repair of a PHILIPS 42PFL6678S TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
Service manual and schematic diagram 42PFL6008S/60 Chassis QFU1.2E LA
CHASSIS QFU1.2E LA FOR MODELS TV PHILIPS:
40PFL8008K, 40PFL8008S
42PFL6008H, 42PFL6008K, 42PFL6008S, 42PFL6158K, 42PFL6158S, 42PFL6188K, 42PFL6188S, 42PFL6198K, 42PFL6678K, 42PFL6678S, 42PFL7008H, 42PFL7008K, 42PFL7008S, 42PFL7008T, 42PFL7108H, 42PFL7108K, 42PFL7108S, 42PFL7108T 46PDL8908S, 46PFL8008K
47PFL6008H, 47PFL6008K, 47PFL6008S, 47PFL6158K, 47PFL6158S, 47PFL6188K, 47PFL6188S, 47PFL6198K, 47PFL6678K, 47PFL6678S, 47PFL7008H, 47PFL7008K, 47PFL7008S, 47PFL7108H, 47PFL7108K, 47PFL7108S
55PDL8908D, 55PDL8908S, 55PDL8908S, 55PFL6008H, 55PFL6008K, 55PFL6008S, 55PFL6008T, 55PFL6158K, 55PFL6158S, 55PFL6188K, 55PFL6188S, 55PFL6198K, 55PFL6678K, 55PFL6678S, 55PFL7008H, 55PFL7008K, 55PFL7008S, 55PFL7108H, 55PFL7108K, 55PFL7108S, 55PFL8008K, 55PFL8008S
60PFL6008H, 60PFL6008K, 60PFL6008S, 60PFL8708S
65PFL9708S
The appearance of MainBoard 310431366185 is shown in the figure below:310431366185
The weak point in the PHILIPS TV models assembled on the QFU1.2E LA chassis is the main board SSB (MainBoard), which usually refuses to work after two years of operation. Replacement required.
The cost of the board is quite high, which sometimes raises the question of the feasibility of repairs.
Despite the efforts of designers to complicate or exclude the possibility of repairing the board, there are still options for its restoration.
Attention to the masters !!! You should pay attention to the drop of compound from the bottom of the board. When trying to heat the board or reball of BGA chips, the compound must be completely removed. Otherwise, the paths will be closed, which will significantly complicate the further repair of the board.
310431366185 can be used in TVs:
PHILIPS 42PFL7008S/60 (Panel LC420EUF (AF)(F1)), PHILIPS 40PFL8008S/60 (Panel LTA400HL18 002), PHILIPS 42PFL6008S/60 (Panel LC420EUF (PF)(F1)), PHILIPS 42PFL7108S/60 (Panel LC420EUF PFF1), PHILIPS 47PFL6008S/60 (Panel LC470EUF (PF)(F1) code 430 p/n: 932230114682), PHILIPS 47PFL6008S/60 (Panel LC470EUF (PF)(F1) code 430 p/n: 932230114682), PHILIPS 47PFL7008S/60 (Panel LC470EUF PFF1 code 430 932230114682), PHILIPS 60PFL6008S/60 (Panel LC600EUD FEF2 code 439 p/n: 932230207682), PHILIPS 55PFL8008S/12 (Panel LTA550HQ25), PHILIPS 55PFL7108S/60 (Panel LC550EUF (PF)(F1)), PHILIPS 42PFL6678S/12 (Panel LC420EUF (PF)(F1)).
The appearance of the power supply
Main features of the PHILIPS 42PFL6678S device:
Installed matrix (LED-panel) LC420EUF (PF) (F1).
The matrix control uses the Timing Controller (T-CON) 6870C-0450A.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a BD9479FV PWM controller.
The necessary supply voltages for all nodes of the PHILIPS 42PFL6678S TV are generated by the power module FSP140-4FS01, or its analogs using chips FSB117H (Standby), FAN7930 (PFC), SSC9522S (PWM).
MainBoard - the main board (motherboard) is a module 310431366185, using chips FUSION120, H5TQ2G63BFR, H5TQ2G83BFR, SPI Flash: 25P10VP. and others.
The SUT-RE214AN H 3D129G tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC420EUF-PFF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 16.7M / 1.06B (8-bit / 8-bit + Dithering), CIE1931 72%
Response Time: 5 (G to G); 8 (MPRT)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: LVDS (4 ch, 8/10-bit), 92 pins
Voltage: 12.0V
