
PHILIPS
Model: 20PFL4122 / 10
Chassis / Version: TPS1.0E LA
Panel: LC201V02
Inverter (backlight): LIPS
PWM Inverter: OZT1060GN (20n) pl
MOSFET Inverter: 4606 (8 pin)
Power Supply (PSU): 715T2572 -1 PWPFA66GR1P
PWM Power: EA1530 (8H) PL
MOSFET Power: BD7R16
MainBoard: 715T2229-2
IC MainBoard: CPU: MST96885LD-LF, DRAM: HY57V641620FTP-6, SPI Flash: 25L8005M2I
Tuner: FQ1216MEV
Control: RC2023611 / 01B 3139 238 14641
PHILIPS
Model: 20PFL4122 / 58
Chassis / Version: LC4.1E AC
Panel: A201SN02 V.5
Inverter (backlight): integrated into PSU
PWM Inverter: UBA2070T (16pin)
Power Supply (PSU): BL6L70PS10 / J2 3122 427 24741
PWM Power: TY72011AP2 (14pin)
MOSFET Power: P16NF06 P5NK50Z
MainBoard: 3139_123_60192 3139 123 60192 Wk534.3
IC MainBoard: CPU: TDA15021H1 / N1C91; Scaler: GM5221H-LF
Tuner: UR1316S / A 3139 147 23021A
Control: RC2023615 / 01 3139 238 15051
Technical Specifications 20PFL4122
PHILIPS 20PFL4122
General recommendations for repairing TV LCD
Like all other televisions, it is advisable to start PHILIPS 20PFL4122 / 58 with a careful inspection of both external and internal elements and modules. Visible damage to elements can sometimes suggest directions for troubleshooting even before the necessary measurements are taken. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
If the power supply module BL6L70PS10 / J2 3122 427 24741 fails, the external manifestations may be different, for example, PHILIPS 20PFL4122 / 58 does not turn on at all and there is no indication of the indicator lights on the front panel. In the absence of swollen filter capacitors of the secondary rectifiers, the diagnostics of the power supply should always be started by checking the fuse and, if it is broken, it is first necessary to check the rectifier bridge diodes and the power switch P16NF06 P5NK50Z for the possibility of an avalanche or thermal breakdown.
In most cases, a breakdown of the N-Fet converter key does not occur for no reason and you should look for other faulty circuit elements that could provoke a defect. This can be dried electrolytic capacitors in the primary circuit, and faulty damper elements, as well as dangling resistors or punched semiconductor elements in the stabilization circuits. Possible defective chip PWM TY72011AP2 (14n) UBA2070 (16n) pl from the manufacturer.
If the power module uses an active KKM circuit (power factor control), troubleshooting is somewhat more complicated.
If the PHILIPS 20PFL4122 / 58 TV does not have an image, but there is sound, the malfunction should be sought in the backlight lamp power converter (inverter). It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the PSU (power supply) for excessive ESR.
When repairing the LIPS inverter, it is often necessary to disable the protection for diagnostics, which, for the purpose of fire safety, turns it off in any emergency situation, for example, during a malfunction or uneven wear of the lamps, which makes it difficult to find a defect.
When diagnosing with the protection off, special precautions must be taken, because there is a risk of failure of the inverter power elements. After the diagnosis, it is imperative to restore the protection circuits for the inverter to operate normally.
Diagnosis and repair of the motherboard is carried out by checking the operability of the stabilizers or power converters of the module chips. In some cases, a software update is required.
Attention to the owners! Attempts at self-repair of the PHILIPS 20PFL4122 / 58 TV are not recommended by the manufacturer and can lead to serious negative consequences!
Service manual and schematic diagram 20PFL4122/58 Chassis LC4.1E AC
MODELS: 20PFL5122, 23PFL5322

3139_123_60192
3139_123_60192 can be used in TVs:
PHILIPS 20PF4110S/58 (Panel LC201V02 (SD)(B1)), PHILIPS 15PF4121/58 (Panel LC150X02 (TL)(01)), PHILIPS 15PF5120/58 (Panel LC150X02), PHILIPS 15PF5121/58 (Panel IDM69E1S51718 Rev:01 QD15XL16 ), PHILIPS 15PF5121/58 (Panel T150XG01 V.3), PHILIPS 20HF5474/10 (Panel LC201V02 (SD)(D1)), PHILIPS 20PF4121/58 (Panel LC201V02 (SD)(B1)), PHILIPS 20PF5120/58 (Panel A201SN02 V4), PHILIPS 20PF5320/58 (Panel LC200WX1 (SL)(01)), PHILIPS 20PFL4101S/60 (Panel LC201V02 SD B1), PHILIPS 20PFL4102S/60 (Panel LC201V02 (SD)(D1)), PHILIPS 20PFL4102S/60 (Panel LC201V02 (CD)(B1)), PHILIPS 20PFL4112S/60 (Panel LC201V02 (SD)(B1)), PHILIPS 20PFL4112S/60 (Panel LC201V02 SD D1), PHILIPS 20PFL4122/58 (Panel A201SN02 V.5), PHILIPS 20PFL5122/58 (Panel A201SN02 V.5), PHILIPS 23PFL5322/58 (Panel T230XW01 V.3), PHILIPS 23PF4321/58 (Panel T230XW01 V.2).
The appearance of the power supply
Main features of the PHILIPS 20PFL4122 device:
Installed matrix (LCD panel) A201SN02 V.5.
To power the backlight, a converter is used, combined with a power supply, controlled by a UBA2070T PWM controller (16pin).
The necessary supply voltages for all nodes of the PHILIPS 20PFL4122 television are generated by the BL6L70PS10 power supply module or its analogs using TY72011AP2 microcircuits (14pin) and power switches of the P16NF06 P5NK50Z type.
MainBoard - the main board (motherboard) is a module 3139_123_60192, using CPU chips: TDA15021H1 / N1C91; Scaler: GM5221H-LF and others.
The tuner UR1316S / A 3139 147 23021A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: A201SN02 V5
Type: a-Si TFT-LCD, Panel
Diagonal size: 20.1 inch
Resolution: 800x600, SVGA
Display Mode: TN, Normally White, Transmissive
Active Area: 408x306 mm
Surface: Antiglare
Brightness: 450 cd / m²
Contrast Ratio: 700: 1
Display Colors: 16.2M (6-bit + FRC), CIE1931 72%
Response Time: 11/5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 6 pcs CCFL Without Driver
Signal Interface: TTL (1 ch, 8-bit), 50 pins
Voltage: 5.0V