Technical description and composition of the BBK LT2610 TV, panel type and applicable modules. The composition of the modules.BBK
Model: LT2610
Panel: V260B1-L02 Rev. C1
Power Supply (PSU): 26HU36S 156795CE1
MainBoard: 26HU36S 156796CE3
Tuner: TDQ6F / W124XC
Control: RC-2603
Technical specifications LT2610S
BBK LT2610
General recommendations for repairing TV LCD
Possible manifestations of defects
- The BBK LT2610 TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
In the vast majority of such cases, a malfunction is detected in the 26HU36S power module. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (PWM). It is checked only by replacement with a known good one.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
The defect can be caused by problems in the nodes or elements of the backlight of the display, or in the power supply of the lamps or inverter. If all the electrolytic capacitors of the filter according to the power supply of the inverter are working, make sure that the lamps are working, then you need to check the converter keys and the secondary windings of the transformers.
If in diagnosing a malfunction, it is necessary to disable the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during work, and after they are finished, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the 26HU36S motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the TDQ6F / W124XC tuner. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
It should be remembered! Attempts to independently repair the BBK LT2610 TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
Service Manual with Schematic Diagram 45 pages on the LT2610S, LT3210S
The appearance of the MainBoard CV7050LA is shown in the figure below:CV7050LA
CV7050LA can be used in TVs:
BBK LT1902S (Panel M190A1-P0A), BBK LT2202S (Panel M216H1-P01), BBK LT2428HD (Panel V236H1-P01 HK236WLCM-CH03H), BBK LT2428S (Panel V236H1-P01), FUSION FLTV-19W6 (Panel M190A1-P0A), IZUMI TL26H615B (Panel M260TWR1).
Main features of the BBK LT2610 device:
Installed matrix (LCD panel) V260B1-L02 Rev. C1.
The formation of the necessary supply voltages for all nodes of the BBK LT2610 TV is carried out by the 26HU36S power module, or its analogues.
MainBoard - the main board (motherboard) is a 26HU36S module.
The TDQ6F / W124XC tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: CMO
Model: V260B1-L02
Type: a-Si TFT-LCD, Panel
Diagonal size: 26.0 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 575.769x323.712 mm
Brightness: 450 cd / m²
Contrast Ratio: 800: 1
Display Colors: 16.2M (6-bit + FRC), CIE1931 72%
Response Time: 3/5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Without Driver
Signal Interface: RSDS (1 Channel), 45 pins
Voltage: 5.3.3 / 5.0V (VDD / VIN5)
BBK LT2610S LCD TV with V2601B1-L02 LCD, 26 "(66 cm) diagonal size in 16: 9 format. 500 cd / m² screen brightness is provided by CCFL (EEFL) fluorescent lamps. Maximum brightness to minimum ratio (contrast) ) is 800: 1. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standard max 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound system 12 W (2x6 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x3, component, SCART, RGB, VGA, HDMI. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in the operating mode from the network is 140 watts.
Overall dimensions: With stand 673x516x208 mm, Without stand 439x296x73 mm.
TV Weight: 19 kg.
Attention! The BBK LT2610S LCD TV panel V2601B1-L02 is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen to avoid permanent damage to the LCD panel!
