Technical description and composition of the HAIER LE32F1000T TV, type of panel and applicable modules. The composition of the modules.HAIER LED
Model: LE32F1000T
Chassis / Version: TP.MS3463S.PB801
Panel: HV320WHB-N80 CN320CN7201
LED backlight: CRH-K323535T02085CS-Rev1.7
T-CON: 32HD Dual Gate_X-PCB-X0.0 47-6001317
LED driver (backlight): integrated into MainBoard
PWM LED driver: SN51DP
MOSFET LED driver: AOD458
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-220
MainBoard: TP.MS3463S.PB801
IC MainBoard: CPU: MSD3463GU, SPI Flash: 25Q64B, AUDIO: OB6220VP
Tuner: XF-3SDT-H
Specifications LE32F1000T
HAIER LE32F1000T
General repair guidelines for TV LCD LED
Possible malfunctions
- The HAIER LE32F1000T TV does not turn on and does not show any signs of turning on, it does not respond to the control buttons or the remote control.
First of all, in such cases, you should verify the operability of the common switching power supply (IIP) - AC / DC voltage converter of the mains voltage. All source elements in this TV model are located on the MainBoard TP.MS3463S.PB801 main board. In the absence of the necessary supply voltages in the secondary circuits of the converters, it is necessary to check the power switches (TO-220) and rectifier diodes for a possible partial or complete breakdown.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
Usually in such cases there is no backlight LED-panel (matrix). Usually the cause of the malfunction is in the breakage of the LEDs, or in the connectors of the LED strips, but sometimes the LED driver also turns out to be faulty.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the TP.MS3463S.PB801 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sometimes they require checking or replacing (if necessary) the elements of the MainBoard - CPU: MSD3463GU, SPI Flash: 25Q64B, AUDIO: OB6220VP. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
If you suspect a malfunction of the XF-3SDT-H tuner, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
It should be remembered! Attempts to self-repair a HAIER LE32F1000T TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-serviceability of the device!
FIRMWARE FOR SPI FLASH ----------> HAIER LE32F1000T, Main: TP.MS3463S.PB801, Panel: HV320WHB-N80 CN320CN7201
The appearance of MainBoard TP.MS3463S.PB801 is shown in the figure below:TP.MS3463S.PB801
TP.MS3463S.PB801 can be used in TVs:
AKAI LEA-40V35M (Panel LSC400HM06), AKIRA 32LED38T2P (Panel ST3151A05-8), AKIRA 32LED02T2M (Panel ST3151A04-9 Ver.2.1), BBK 32LEM-1029/TS2C (Panel C320X16-E18-H), BBK 39LEM-1033/TS2C (Panel C390X15-E8-A G01), BBK 32LEM-1026/TS2C (Panel CX315DLEDM ST3151A05-8), BBK 32LEM-1027/TS2C (Panel ST3151A05-8 / CX315DLEDM), DEXP F43C7100K (Panel LC430DUY (SH)(A1)), DEXP F42B7000M (Panel V420HJ2-P01), DEXP F43C7000C (Panel C430F14-E1-L / LC430DUY), DEXP F40B7100K (Panel LSC400HN02-G02 40N06-L-HPX1F1), DEXP H28C7100C (Panel C275X15-E1-H (G31)), DEXP H32C7300K (Panel LSC320AN02), DEXP H32D7100C (Panel ST3151A05-8 Ver2.5), DEXP H28D7300K (Panel HV280WX2-260), ERISSON 32LES78T2W (Panel KM0320LDRH0037), ERISSON 32LEE30T2 (Panel LK315T3HB87-12V), SUPRA STV-LC32T560WL (Panel LSC320AN10), SUPRA STV-LC32T550WL (Panel LSC320AN02), SUPRA STV-LC40T500WL (Panel C39X15-E7-A), TELEFUNKEN TF-LED32S45T2 (Panel LK315T3HB87-12V), THOMSON T39D20DH-01B (Panel T390XVN01.0).
Key Features of HAIER LE32F1000T:
Installed matrix (LED-panel) HV320WHB-N80 CN320CN7201.
The matrix control uses the Timing Controller (T-CON) 32HD.
To power the backlight LEDs, a converter is used, combined with the TP.MS3463S.PB801 main board, controlled by the SN51DP PWM controller. As power elements of the LED driver, keys of the AOD458 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits and TO-220 type power switches.
MainBoard - the main board (motherboard) is a TP.MS3463S.PB801 module, using CPU chips: MSD3463GU, SPI Flash: 25Q64B, AUDIO: OB6220VP and others.
The XF-3SDT-H tuner allows you to receive television programs and tune to channels.
HAIER LE32F1000T TV with HV320WHB-N80 LCD, 28 "(71 cm) diagonal size in 16: 9 format. The required screen brightness of 200 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1200: 1. LED TV backlighting technology is implemented in the TV screen manufacturing technology of this TV model. HD images can be viewed in high resolution at 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). Supported media file formats: MP3, JPEG.
The power of the sound system 12 W (2x6 W) provides two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x3, USB.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV working in the network mode is 50 watts.
Overall dimensions: with stand 730x466x207 mm, without stand 730x430x75 mm.
TV Weight: 4 kg.
Attention! The HV320WHB-N80 CN320CN7201 panel of the HAIER LE32F1000T LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
