Technical description and composition of the LG 47LB671V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 47LB671V
Chassis / Version: LD42B
Panel: LC470DUH (PG) (F1)
LED backlight: 6920L-0504A, 6920L-0505A, 6920L-0506A, 6920L-0507A
LED driver (backlight): integrated into PSU
Power Supply (PSU): EAX65424001 (2.4) LGP4750-14LPB
PWM Power: MAP8800 (PFC), ICE3BR4765JZ (Standby)
MainBoard: EAX65384004 (1.5) EBR78599402
IC MainBoard: CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C
Tuner: TDJM-G101D EBL61400501
Control: AKB73975729; WiFi 2703H-LGSBW41, BEJLGSBW41, EAT62093301
Specifications 47LB671V
LG 47LB671V
General repair guidelines for TV LCD LED
A malfunction of the power supply is often manifested corny - the TV does not turn on, does not make any sounds, does not light up and does not blink with any indicators. After checking the mains fuse and power elements of the primary power supply circuit, it should also check the absence of a short circuit in the loads of the secondary rectifiers.
Mos-Fet keys used in switching power supplies (SMPS) rarely fail for no reason to look for when checking other circuit elements. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The ICE3BR4765JZ PWM controller chip may also cause a breakdown of the power switch of the converter.
If the image appears and immediately disappears when the TV is turned on, or it is initially absent when it is turned on, but the sound has other functions, there is a high probability of a malfunction of the display backlight LEDs or the LED driver (power converter for the LC470DUH (PG) panel backlight assembly (F1)).
In most cases of lack of backlight, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
In cases of attempts to repair the motherboard EAX65384004 (1.5) EBR78599402, it is necessary to check the operability of the linear stabilizers and power converters of its microcircuits and, if possible, update the software (software). BGA chips can sometimes be diagnosed with local heating.
In cases of attempts to repair the MB board (SSB), it is necessary to check the health of its elements - CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the TDJM-G101D EBL61400501 tuner. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
It should be remembered! Attempts to repair the LG 47LB671V TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
Service manual and schematic diagram ---------------> LG 47LB671V Chassis LD42B.
CHASSIS : LD42B; MODEL : 47LB67**, 47LB67**-Z*, 47LB700V, 47LB700V-ZG
Backlight LED:
47 V14 sDRT REV0.8 6 L2-Type 6920L-0507A;
47 V14 sDRT REV0.8 6 L1-Type 6920L-0505A;
47 V14 sDRT REV0.8 6 R2-Type 6920L-0506A;
47 V14 sDRT REV0.8 6 R1-Type 6920L-0504A
User Manual WiFi -------------------------------> LG Wi-Fi Module LGSBW41
The appearance of the MainBoard EAX65384004 is shown in the figure below:EAX65384004
EAX65384004 can be used in TVs:
LG 32LB650V ZE (Panel LC320DUH (FG)(P2)), LG 47LB650V ZE (Panel LC470DUH (FG) (P2)), LG 42LB650V (Panel LC420DUH (FG)(P2)), LG 42LB671V ZF (Panel LC420DUH (PG) (F1)), LG 47LB671V (Panel LC470DUH (PG)(F1)), LG 42LB653V ZK (Panel LC420DUH (FG)(P1)), LG 42LB720V (Panel LC420DUH (PG)(F1)), LG 42LB658V (Panel LC420DUH (FG)(P2)), LG 47LB677V (Panel LC470DUH (FG)(F1)), LG 42LB679V (Panel LC420DUH (PG)(F1)), LG 47LB653V (Panel LC470DUH (FG)(P1)), LG 32LB653V (Panel LC320DUH( FG)(P1)), LG 42LB690V (Panel LC420DUH (PG)(F1)), LG 55LB630V (Panel LC550DUH).
PSU Advanced
On the 47LB671V TV, the EAX65424001 power module is installed using the PFC (Power Factor Correction) scheme acting as an active filter to eliminate the higher harmonic components of the current consumption. The boost converter based on the MAP8800 PWM controller does not allow the input rectifier filter's electrolytic capacitor to be connected to the network directly through open diodes, when the reactance (about 15-30 ohms at a frequency of 50 Hz) determines the charge current. As a result of the conversion, the charging current of the capacitor will be determined in such a way that the envelope of the high-frequency pulses of the input current will repeat the phase and shape of the sine wave of the input voltage. The health check of the PFC unit is carried out by measuring the DC voltage on the capacitor of the rectifier network. In operating mode, it should be around 380V, in standby approximately 300V.
The appearance of the power supply
Main features of the device LG 47LB671V:
Installed matrix (LED-panel) LC470DUH (PG) (F1).
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the LG 47LB671V TV are generated by the EAX65424001 power module or its analogs using MAP8800 (PFC), ICE3BR4765JZ (Standby) microcircuits.
MainBoard - the main board (motherboard) is an EAX65384004 module, using CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C and others.
Tuner TDJM-G101D EBL61400501 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC470DUH-PGF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 47 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 1039.68x584.82 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 1.06B (8-bit + Dithering), CIE1931 72%
Response Time: 8/10 (Tr / Td)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: EPI, 100 pins
Voltage: 12.0V
