LG LED
Model: 50LA667S
Chassis / Version: LD33B
Panel: T500HVD02.1
LED backlight: 7030PKG 60EA R-TYPE / L-TYPE
T-CON: T420HVD02.2
LED driver (backlight): V352101 4H + V3526.011 / C
Power Supply (PSU): EAX64908101 LGP4755-13P
PWM Power: L6599AD, R2A20133DSP (PFC), FSD106LG (Stb)
MOSFET Power: STD13NM60N
MainBoard: EAX64797003 (1.2)
IC MainBoard: LGE2122, SAA36403538, H5TQ4G63AFR, H5TQ2G63AFR, NTP7513
Tuner: TSQ-G601D (B) EBL61240503
Specifications 50LA667S
LG 50LA667S
General repair guidelines for TV LCD LED
Possible malfunctions
- The LG 50LA667S TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
In some of these cases, the main switching power supply, the EAX64908101 module, is faulty. It is necessary to measure its output voltages, and if they are absent, check the operability of the power switches (STD13NM60N) of the converters and rectifier diodes for a short circuit probability.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) L6599AD, R2A20133DSP (PFC), FSD106LG (Stb), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the EAX64797003 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sometimes it is necessary to check or replace (if necessary) the elements of the MainBoard board - LGE2122, SAA36403538, H5TQ4G63AFR, H5TQ2G63AFR, NTP7513. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
Before replacing the tuner TSQ-G601D (B) EBL61240503, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Once again, remind users! Attempts to self-repair the TV LG 50LA667S without the appropriate qualifications and the necessary experience can lead to its complete unrepairability!
Service manual / schematic diagram ------------> LG 50LA667S Chassis LD33B.
PSU schematic diagram ------------> LGP4755-13P EAX64908101 Power Supply schematic diagram
The appearance of the MainBoard EAX64797003 is shown in the figure below:
EAX64797003
EAX64797003 can be used in TVs:
LG 42LA620V (Panel LC420DUE (SF)(U1)), LG 32LN570V (Panel LC320DUE (SF)(R1)), LG 50LA644V (Panel LC500EUN (SF)(F1)), LG 47LA660V (Panel LC470EUG (PF)(F1)), LG 47LA621V (Panel LC470DUE (SF)(U1)), LG 42LA644V (Panel LC420EUN (SF)(F2)), LG 39LA620V ZA (Panel T390HVJ01.0), LG 42LA621V ZD (Panel LC420DUE (SF)(U1)), LG 32LA621V ZD (Panel LC320DUE (SF)(U1)), LG 32LN655V (Panel LC320EUB (PF)(M1)), LG 42LA667V (Panel LC420EUH (PF)(P1) ), LG 47LN613V (Panel LC470DUE (SF)(R4)), LG 32LA667V ZB (Panel LC320EUB (PF)(P1)), LG 55LA660V ZA (Panel LC550EUH (PF)(P1)), LG 47LA620V ZA (Panel LC470DUE (SF)(U1)), LG 32LN613V ZB (Panel LC320DUE (SF)(R4)), LG 42LN655V ZB.BRUZLJU (Panel LC420EUH (PF)(M1)), LG 32LA644V ZA (Panel LC320EUN (SF)(F1)), LG 42LN613V (Panel LC420DUE (SF)(R4)), LG 47LA690V ZB (Panel LC47EUH (PF)(P1)), LG 47LA662V (Panel LC470EUG (PF)(F1)), LG 42LA645V 42LA645V-ZC.BRUYLJU (Panel LC420EUN (SF)(F3)), LG 32LA660V (Panel LC320EUB (PF)(P1)), LG 47LA644V 47LA644V-ZA (Panel LC470EUN (SF)(F2)), LG 50LA667S (Panel T500HVD02.1), LG 47LA691V (Panel LC470EUH (PF)(P1)), LG 32LA662V (Panel LC320EUB (PF)(P1)).
The appearance of the power supply
Main features of the device LG 50LA667S:
Installed matrix (LED panel) T500HVD02.1.
The matrix control uses the Timing Controller (T-CON) T420HVD02.2.
The LED driver V352101 is used to power the backlight LEDs.
The necessary supply voltages for all nodes of the LG 50LA667S TV are generated by the EAX64908101 power supply module or its analogs using L6599AD, R2A20133DSP (PFC), FSD106LG (Stb) microcircuits and STD13NM60N type power switches.
MainBoard - the main board (motherboard) is an EAX64797003 module using LGE2122, SAA36403538, H5TQ4G63AFR, H5TQ2G63AFR, NTP7513 and other chips.
The tuner TSQ-G601D (B) EBL61240503 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: T500HVD02.1
Type: a-Si TFT-LCD, Panel
Diagonal size: 50 inch
Resolution: 1920x1080, FHD
Display Mode: AMVA3, Normally Black, Transmissive
Active Area: 1095.84x616.41 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 400 cd / m²
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 5.5 (G to G)
Frequency: 120Hz
Lamp Type: WLED Embedded (LED Driver)
Signal Interface: LVDS (4 ch, 8-bit)
Voltage: 12.0V