Technical description and composition of the TV SHARP LC-32S2RU, type of panel and applicable modules. The composition of the modules.diagramSHARP
Model: LC-32S2RU
Panel: T315XW01 V.5
T-CON: T315XW01 V.5 contrl / 260XW02 contrl
Inverter (backlight): 4H.V1448.291 / B1 DARFON
PWM Inverter: OZ964SN
Trans Inverter: 4004L612.313 (GP)
Power Supply (PSU): CEF213A
PWM Power: STR-W6765, STR-X6768N
MainBoard: CEF170A
IC MainBoard: MST9883C, NJM2584AM, SII9011CLU, AN15853B, R8J66607A72FP, OEC7166A, MM1501XNRE, TA2024
Tuner: TAFV-W322D
Control: GA515WJSA, IR: CEF215A
Technical Specifications LC-32S2RU
SHARP LC-32S2RU
General recommendations for repairing TV LCD
It is advisable to start repairing a SHARP LC-32S2RU TV, like any others, with an examination of the internal and external visible physical visual changes. Often, by the external signs and nature of some damage, it is possible to draw preliminary conclusions and determine a further algorithm for troubleshooting. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
In the absence of any signs of operability, when the SHARP LC-32S2RU does not turn on and does not signal anything with the control lights on the panel, the power module is most likely faulty. If the mains fuse is broken in the power supply, in most cases a breakdown of the power switch is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
In most cases, a breakdown of the N-Fet converter key does not occur for no reason and you should look for other faulty circuit elements that could provoke a defect. This can be dried electrolytic capacitors in the primary circuit, and faulty damper elements, as well as dangling resistors or punched semiconductor elements in the stabilization circuits. Possible defective PWM chip from the manufacturer.
In cases where the Power Factor Corrector (PFC) is used in the power supply, troubleshooting can be a bit more complicated.
If the SHARP LC-32S2RU does not have an image, but there is sound, there is a possibility of a malfunction of the backlight or power converter. You should also make sure that the electrolytic capacitors of the secondary rectifiers of the common power supply are working.
Repairing the inverter is difficult because in case of any malfunction or emergency, even with uneven wear of the lamps, a protection is triggered, which turns it off for fire safety. Diagnostics become impossible and protection needs to be disabled.
It should be remembered that when the protection is turned off, there is always a risk of failure of the power elements of the inverter during diagnosis. After repair, it is necessary to restore all standard converter protection circuits.
Attention to the owners! Attempts to repair the TV SHARP LC-32S2RU by yourself are not recommended by the manufacturer and can lead to serious negative consequences!
Service manual / schematic diagram --------------> Sharp LC-32S2RU
The appearance of the MainBoard CEF170A is shown in the figure below:CEF170A
The appearance of the power supply
Main features of the SHARP LC-32S2RU device:
Installed matrix (LCD panel) T315XW01 V.5.
The matrix control uses the Timing Controller (T-CON) T315XW01.
To power the backlight, an inverter 4H.V1448.291 is used, it is controlled by the PWM controller OZ964SN. A transformer 4004L612.313 (GP) is installed in the inverter converter.
The necessary supply voltages for all nodes of the SHARP LC-32S2RU television are generated by the power supply module CEF213A, or its analogs using microcircuits STR-W6765, STR-X6768N.
MainBoard - the main board (motherboard) is a CEF170A module, using microcircuits MST9883C, NJM2584AM, SII9011CLU, AN15853B, R8J66607A72FP, OEC7166A, MM1501XNRE, TA2024 and others.
The TAFV-W322D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: AUO
Model: T315XW01 V5A
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: AMVA, Normally Black, Transmissive
Active Area: 697.68x392.26 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 500 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit)
Response Time: 15/5 (Tr / Td); 8 (G to G)
Frequency: 60Hz
Lamp Type: CCFL Embedded (Inverter)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V
LCD TV SHARP LC-32S2RU with LCD T315XW01, diagonal size 32 "(81 cm) 16: 9 format. The brightness of the screen 500 cd / m² is organized by backlighting with CCFL fluorescent lamps (EEFL). Contrast, as the ratio of maximum brightness to minimum, not less than 800: 1.
You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound speaker system 20 W (2x10 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART x2, RGB, VGA, HDMI. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV from the network in operating mode is 170 watts.
Overall dimensions: 818x657x274 mm.
TV Weight: with stand: 17.1 kg, without stand: 15 kg.
Attention! The T315XW01 V.5 panel of the SHARP LC-32S2RU LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen to avoid permanent damage to the LCD panel!
