Technical description and composition of the TV SHARP LC-60LE651RU, type of panel and applicable modules. The composition of the modules.SHARP LED
Model: LC-60LE651RU
Panel: R1JE600D3GV2AY
Power Supply (PSU): FSP-202-4SF
MainBoard: DUNTKG135 - QPWBXG135WJN2 - DUNTKG135FM12
IC MainBoard: CPU: MT41J128M16JT; NAND Flash: MT29F2G08ABAEAWP; SOUND: STA333BW
Control: GB067WJSA
Technical Specifications LC-60LE651
SHARP LC-60LE651RU
General repair guidelines for TV LCD LED
Repair of all electronic devices, including the SHARP LC-60LE651RU TV, it is advisable to start with an external examination of its external and internal elements. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. Ring cracks in the soldering of the leads of the heating elements, swollen electrolytic capacitors, a charred paint layer on the resistors - all this for the repairman can be a significant clue in the assumptions about the causes and consequences of the malfunction.
In the absence of any signs of operability, when the SHARP LC-60LE651RU does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the TV's FSP-202-4SF power module. With the same manifestations, the power regulator of the control processor on the motherboard may be faulty. When diagnosing and repairing the power supply, after replacing the swollen capacitors of the filters of the secondary rectifiers (if any), you must first check the mains fuse. When it is broken, the power elements of transistors and rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or broken resistors in its bundle.
Sometimes the SHARP LC-60LE651RU TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the converter for the backlight LEDs of the R1JE600D3GV2AY panel, or a break in the LED circuit is possible. In such cases, first of all, it is necessary to verify the serviceability of all the electrolytic capacitors of the filter by supplying the LED driver itself, including in the power supply unit (power supply unit).
In most cases of lack of backlight, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
An open in the LED lines connected in series cannot be detected using a multimeter or tester without disassembling the panel. To open all the transitions, several tens of volts are needed, and it is best to use a current source for such purposes.
Remember! Attempts to self-repair by users of the SHARP LC-60LE651RU TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!
The appearance of the MainBoard DUNTKG135 is shown in the figure below:DUNTKG135
DUNTKG135 can be used in TVs:
SHARP LC-39LE751RU (Panel V390HK1-LE6 Rev. C4), SHARP LC-60LE651RU (Panel R1JE600D3GV2AY).
Main features of the SHARP LC-60LE651RU device:
Installed matrix (LED panel) R1JE600D3GV2AY.
The formation of the necessary supply voltages for all nodes of the SHARP LC-60LE651RU TV is carried out by the FSP-202-4SF power module, or its analogues.
MainBoard - the main board (motherboard) is a DUNTKG135 module using CPU chips: MT41J128M16JT; NAND Flash: MT29F2G08ABAEAWP; SOUND: STA333BW and others........
SHARP LC-60LE651 LED TV with R1JE600D3GV2AY LCD, 60 inches (152 cm) diagonal, 16: 9 aspect ratio. The brightness of the screen 390 cd / m² is provided by LED backlight. Contrast, as the ratio of maximum brightness to minimum, is 5000: 1. This model uses backlight with the end position of the LEDs (relative to the screen) - Edge LED.
There is support for 3D images with active (shutter) technology for separating the right and left channels.
The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD).
The LC-60LE651 TV is equipped with SMART software, as well as the ability to work with applications and on the Internet. Connecting to a network can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p.
Supported media file formats: MP3, DivX, JPEG.
Sound power 30 W (2x15 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, RGB, VGA, HDMI x4, USB, Ethernet (RJ-45). An output for connecting headphones is provided.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
The power consumed by the TV from the network in operating mode is 100 watts.
Overall dimensions: With stand 662x429x170 mm, Without stand 662x403x68 mm.
TV Weight: 29.6 kg.
Attention! The R1JE600D3GV2AY panel of the SHARP LC-60LE651 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
