Technical
description and composition of the FUSION FLTV-22W6 TV, panel type and
applicable modules. The composition of the modules.FUSION LED
Model: FLTV-22W6
Chassis / Version: B.SPC81B-1 9245
Panel: CLAA215FA
LED driver (backlight): integrated into PSU
PWM LED driver: BIT3713
MOSFET LED driver: 4606
Power Supply (PSU): LK-PI190414CF
PWM Power: GR8876
MainBoard: B.SPC81B-1 9245
IC MainBoard: SPI Flash: EN25T80_U11; EEPROM: 24C32_U13;
Tuner: ET6T1E-LF-108W-A
Technical Specifications FLTV-22W6
FUSION FLTV-22W6
General repair guidelines for TV LCD LED
The FUSION FLTV-22W6 TV, like many other electronic devices, it is advisable to start repairing by inspecting all external and internal elements. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and determine the direction of further troubleshooting even before the necessary measurements are taken. If ring cracks are detected in the soldering of the terminals of the elements or dangling connecting tracks, swollen capacitors or charred resistors - all this can be characteristic signs of the causes or consequences of an already known typical malfunction.
If the FLTV-22W6 TV does not turn on, does not make any sounds when it is turned on, and also no indicators on the front panel light or blink - there is a high probability of a malfunction in the power module. In some cases, there may be a malfunction only in standby power. In the absence of swollen filter capacitors of the secondary rectifiers, the diagnostics of the power supply should begin by checking the fuse and, if it is broken, it is first necessary to check all the power semiconductor elements of the primary circuit - diodes and transistors for the possibility of an avalanche or thermal breakdown.
It should be borne in mind that in the practice of repair it is extremely rare that key transistors in switching power supplies (SMPS) fail for no reason that should be sought by checking other components, for example, a breakdown of the key can provoke faulty elements of the damper circuits, or dried electrolytic capacitors or dangling primary resistors BP circuits involved in the stabilization process. In this case, all semiconductor elements of the binding of the PWM controller microcircuit are subject to verification, which it is desirable to verify by replacement.
If there is no image when you turn on the FUSION FLTV-22W6, or it appears and immediately disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the CLAA215FA panel, or in their power converter.
In most cases of lack of illumination, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up one LED slightly if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the SPI Flash elements: EN25T80_U11; EEPROM: 24C32_U13; . BGA chip malfunctions are usually easy to detect by warming up.
If the TV works normally from external devices, but does not tune into television channels, the tuner ET6T1E-LF-108W-A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention to the owners! Attempts to self-repair the FUSION FLTV-22W6 TV are not recommended by the manufacturer and can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-22W6, Main: B.SPC81B-1 9245, Panel: CLAA215FA
The appearance of the MainBoard B.SPC81B-1 is shown in the figure below:B.SPC81B-1
B.SPC81B-1 can be used in TVs:
AKAI LTC-15S04 LTC-15S04M (Panel LTA150XH-L06), BBK LD2424HDU (Panel HT235F01-100), FUSION FLTV-19W6 (Panel M190A1-P0A), FUSION FLTV-22W6 (Panel CLAA215FA), IZUMI TL22F405R (Panel M215HW01 V.0), IZUMI TL22F405B (Panel M215HW01 V.0), IZUMI TL19H405B (Panel M190MWW3).
Main features of the FUSION FLTV-22W6 device:
Installed matrix (LED-panel) CLAA215FA.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a BIT3713 PWM controller. As the power elements of the LED driver, keys of type 4606 are used.
The necessary supply voltages for all nodes of the FUSION FLTV-22W6 TV are generated by the LK-PI190414CF power module, or its analogs using GR8876 microcircuits.
MainBoard - the main board (motherboard) is a B.SPC81B-1 module, using SPI Flash chips: EN25T80_U11; EEPROM: 24C32_U13; and others.
The ET6T1E-LF-108W-A tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: CPT
Model: CLAA215FA01A
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Glare (Haze 0%)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 5 (Tr + Td)
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
FUSION FLTV-22W6 TV with a CLAA215FA LCD display, diagonal size 22 "(55 cm) in 16: 9 format. The brightness of the screen is 300 cd / m² with CCFL (EEFL) fluorescent lamps. Contrast, as the ratio of maximum brightness to minimum, is 800: 1. Dynamic contrast ratio of 2500: 1 is provided by special control of the backlight depending on the brightness of the plot. ). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation takes place in the standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the sound system 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, S-Video, SCART, VGA, HDMI. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV working in the network mode is 70 watts.
Overall dimensions: 590x446x160 mm.
TV Weight: 5.7 kg.
Attention! The CLAA215FA panel of the FUSION FLTV-22W6 LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen surface to avoid permanent damage to the LCD panel!
