Technical description and composition of the FUSION FLTV-23L18B TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-23L18B
Chassis / Version: V1L05
Panel: LTA230AP01
LED driver (backlight): 40-24D20D-DRF2XG
Power Supply (PSU): Adapter
MainBoard: 40-MS8200-MAD2XG (V8-MS82AGS-LF1V108)
IC MainBoard: CPU MST6E182VS-LF-Z1, Flash GD25Q32
Tuner: TDQ-3CB
Control: IR: BUTTON 40-L32D21-FBG2XG
Technical Specifications FLTV-23L18B
FUSION FLTV-23L18B
General repair guidelines for TV LCD LED
A malfunction of the power supply is often manifested corny - the TV does not turn on, does not make any sounds, does not light up and does not blink with any indicators. It is advisable to start the troubleshooting of the power supply module by checking the condition of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
It should be borne in mind that in the practice of repair it is extremely rare that key transistors in switching power supplies (SMPS) fail for no reason that should be sought by checking other components, for example, a breakdown of the key can provoke faulty elements of the damper circuits, or dried electrolytic capacitors or dangling primary resistors BP circuits involved in the stabilization process. In this case, all the semiconductor elements of the binding of the IC_Power PWM regulator chip are subject to verification, which it is desirable to verify by replacement.
If there is no image when you turn on the FUSION FLTV-23L18B, or it appears and immediately disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the LTA230AP01 panel, or in the LED node of the driver-converter of their power supply.
In most cases of lack of illumination, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
If the motherboard 40-MS8200-MAD2XG (V8-MS82AGS-LF1V108) is faulty, first of all you need to check all the linear stabilizers and power converters of its chips, and also, if necessary, update the software (software). Sometimes you can check the health of MB only by replacement.
Board repair and replacement of CPU chips MST6E182VS-LF-Z1, Flash GD25Q32 are carried out with the necessary equipment, and the corresponding element base. Malfunctions associated with the application of the soldering technology of the BGA processor can be localized by the heating method.
If there is no reception of television channels, but the TV is working properly from external devices, first of all you need to check the power supply of the TDQ-3CB tuner and update the software. The pulses from the I2C bus must be monitored using an oscilloscope.
It should be remembered! Attempts to repair the FUSION FLTV-23L18B TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-repairability of the device!
The appearance of the MainBoard 40-MS8200-MAD2XG is shown in the figure below:40-MS8200-MAD2XG
40-MS8200-MAD2XG can be used in TVs:
ERISSON 39LET30 (Panel V390HJ1-P01), ERISSON 32LET30 (Panel V32D30-CSOT V2), FUSION FLTV-23L18B (Panel LTA230AP01), GoldStar LT-19A310R (Panel M185XW01 V.F), HYUNDAI H-LED32V8 (Panel T315XW06 V.8).
Main features of the FUSION FLTV-23L18B device:
Installed matrix (LED-panel) LTA230AP01.
The LED driver 40-24D20D-DRF2XG is used to power the backlight LEDs.
To power all the internal nodes of the FUSION FLTV-23L18B TV, an external adapter type source is used.
MainBoard - the main board (motherboard) is a 40-MS8200-MAD2XG module, using CPU chips MST6E182VS-LF-Z1, Flash GD25Q32 and others.
The TDQ-3CB tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTA230AP01
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.0 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 508.152x285.696 mm
Surface: Antiglare
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 68%
Response Time: 8 (G to G)
Frequency: 60Hz
Lamp Type: 11S3P WLED Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
The FUSION FLTV-23L18B TV with an LTA230AP01 LCD display, diagonal size 23 "(58 cm) in 16: 9 format. The required brightness of the screen is 250 cd / m² LED backlight LED. Dynamic contrast ratio of 20,000: 1 is achieved by special control of the LEDs. V The LED panels of this TV are equipped with edge LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i Supported media file formats: MP3, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV x2, component, VGA, HDMI, USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV working in the network mode is 30 watts.
Overall dimensions: with stand 588x412x170 mm, without stand 588x368x72 mm.
TV Weight: 5 kg.
Attention! The panel of the FUSION FLTV-23L18B LED TV LTA230AP01 is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
