Technical description and composition of the FUSION FLTV-40LF28B TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-40LF28B
Chassis / Version: V1M05
Panel: DBMS400LK01-A
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536 (6pin)
MOSFET Power: 7N60 - N-FET 600V 7A
MainBoard: TP.VST59.P83
IC MainBoard: CPU: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2
Tuner: CDT-3NP5I1-10
Technical Specifications FLTV-40LF28B
FUSION FLTV-40LF28B
General repair guidelines for TV LCD LED
Possible malfunctions
- The FUSION 40LF28B TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
In this case, first of all, you should check the operability of the main power source - the AC / DC network voltage converter, all of whose elements are located on the MainBoard TP.VST59.P83 board. In the absence of the necessary supply voltage in the secondary circuits of the converters, it is necessary to check the power switches (7N60 - N-FET 600V 7A) and rectifier diodes for a possible partial or complete breakdown.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6 LD7536 (6pin), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
The most likely in these cases is a malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the TP.VST59.P83 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
If there is no reception of television channels, but the TV is working properly from external devices, first of all it is necessary to check the voltage of the tuner CDT-3NP5I1-10 and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Owners and users of the FUSION 40LF28B TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> TP.VST59.P83-65W18
FIRMWARE FOR SPI FLASH -----------> FUSION 40LF28B V1M05, Main: TP.VST59.P83, Panel: DBMS400LK01-A
The appearance of MainBoard TP.VST59.P83 and voltage measurements at the test points are shown in the figure below:TP.VST59.P83
The TP.VST59.P83 motherboard is combined with a power module and is an independent device made on the basis of the TSUMV59Xxx multifunction processor. Repair of such a board must begin by checking the power batteries, as well as the operability of the voltage converters and linear stabilizers necessary to provide power to certain processor nodes, in particular: + 1.2V core power, built-in DDR + 1.8V memory, and Stand- by 3.3V. The voltage of the LCD panel 5V or 12V, depending on the type of panel used, must be checked directly on the LVDS connector.
TP.VST59.P83 can be used on TVs:
AKAI LEA-28A08W (Panel ST2751A01-1), ERISSON 39LEN52 (Panel TLV3931-02), ERISSON 32LEN52 (Panel TLV3231-01), FUSION FLTV-32L28B (Panel TH315B051-MD1), FUSION FLTV-39LF28B (Panel V390HJ1-P02), FUSION FLTV-32L41B (Panel DBMS315LK09-C), FUSION FLTV-40LF28B (Panel DBMS400LK01-A), HYUNDAI H-LED32V18 (Panel CX315DLEDM T320XVN02.A ), MYSTERY MTV-4023LW (Panel CX390DLEDM / T390HVN04.0), ROLSEN RL-39D1305F (Panel V390HJ1-P02 Rev. C1), RUBIN RB-32D3U (Panel T320XVN01.0), RUBIN RB-39D3F (Panel CX390DLEDM), SHIVAKI STV-40LED5 (Panel V390HJ1-P01 Rev C1), SUPRA STV-LC3225AWL (Panel TH315B051-MD2), SUPRA STV-LC32T810WL (Panel TC315F3E5-A), SUPRA STV-LC32880WL (Panel HE315GH-E77GM\PW1 ), SUPRA STV-LC2825WL (Panel SM275TC30), SUPRA STV-LC32820WL (Panel TC315FJE1-MD4), SUPRA STV-LC32810WL (Panel TC315F3E5-A), TELEFUNKEN TF-LED32S7 (Panel ST3151A05-5 CX315DLEDM).
Main features of the FUSION FLTV-40LF28B device:
Installed matrix (LED-panel) DBMS400LK01-A.
To power the backlight LEDs, a converter is used, combined with the TP.VST59.P83 main board, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 LD7536 microcircuits (6pin) and power switches of the 7N60 type - N-FET 600V 7A.
MainBoard - the main board (motherboard) is a TP.VST59.P83 module, using CPU chips: TSUMV59XE, SPI FLASH: W25Q32BVS, AUDIO: TPA3110D2 and others.
The tuner CDT-3NP5I1-10 provides the reception of television programs and tuning to channels.
FUSION FLTV-40LF28B TV with DBMS400LK01-A LCD, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 350 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 80000: 1 is achieved by special control of the LEDs The LED-panel of this TV is equipped with LED end-lighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM , NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 16 W (2x8 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Attention! The DBMS400LK01-A panel of the FUSION FLTV-40LF28B LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
