Technical description and composition of the FUSION FLTV-D22H11 TV, panel type and applicable modules. The composition of the modules. FUSION LED
Model: FLTV-D22H11
Chassis / Version: T.MS6M181.7A 11203
Panel: LQ215M1LGN2
MainBoard: T.MS6M181.7A 11203
IC MainBoard: CPU: MST6E181VS-LF-Z1; SPI Flash: 25Q32SIP;
Tuner: AFT7 / W130G
Technical Specifications FLTV-D22H11
FUSION FLTV-D22H11
General repair guidelines for TV LCD LED
FUSION FLTV-D22H11, like other televisions, it is advisable to start repairing by inspecting external and internal elements and modules. Specific external damage to some elements can sometimes indicate further actions to determine the malfunction of the TV and localize the defect before the necessary measurements are taken. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in soldering will help the master to guess the causes and possible consequences of the malfunction.
A malfunction of the power supply is often manifested corny - the TV does not turn on, does not make any sounds, does not light up and does not blink with any indicators. When repairing the power supply, it is advisable to start the diagnostics by checking the mains fuse and the electrolytic capacitors of the filters of the converter secondary rectifiers. In the event of a fuse breaking, the reason should be sought in the power semiconductor elements of the pulse converter of the main power supply. First of all, it is necessary to check the diodes of the rectifier bridge of the mains voltage and the power key (s) of the converter. The complete inoperability of the power supply unit can be caused by a short circuit in the power elements in the primary circuit, followed by an open fuse, or a short circuit in the loads.
The reasons for the breakdown of the power switch in pulsed power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or broken resistors in its wiring.
If the FUSION FLTV-D22H11 does not have an image, but there is sound and the TV is controlled by the remote control, a malfunction in the backlight circuits of the LQ215M1LGN2 panel is likely. The LEDs or the power converter - LED driver may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the LED driver, and check the LEDs, connecting obviously known good diagnostics.
The lack of backlight often occurs due to an open circuit in the LED circuit. There is a need for disassembling the panel and checking the LEDs themselves, as well as the same contact connections in the connectors and rations of the terminals.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
Repair of the motherboard T.MS6M181.7A 11203 must begin with the diagnosis and verification of all linear stabilizers and power converters of its microcircuits. Sometimes it may be necessary to update the software (software) - flashing FLASH or EEPROM.
In cases of attempts to repair the MB board (SSB), it is necessary to check the health of its elements - CPU: MST6E181VS-LF-Z1; SPI Flash: 25Q32SIP; which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).In the absence of tuning to local television channels, you should make sure the software is correct, as well as the presence of supply voltages at the terminals of the AFT7 / W1306 tuner.
Once again, remind users! Attempts to independently repair the FUSION FLTV-D22H11 TV without the appropriate qualifications and experience can lead to its complete non-repairability!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-D22H11, Main: T.MS6M181.7A 11203, Panel: LQ215M1LGN2
The appearance of MainBoard T.MS6M181.7A is shown in the figure below:Repairing the motherboard T.MS6M181.7A, which uses the multi-function processor MST6M181VS combined with a scaler, is advisable to start by checking the power supply of the standby mode, which is implemented using a separate linear stabilizer 3.3V. Further, in the operating mode, it is necessary to check the operability of linear stabilizers or voltage converters necessary to provide power to the processor nodes: 1.2V, 2.5V, 3.3V. A voltage of 2.5V is required to power the DDR W9425G6JH memory. If there is a backlight and no image, the power of the LCD panel 5V or 12V, depending on the type of panel used, it is advisable to measure directly on the LVDS connector. If the TV does not exit Stand-by, does not respond to the remote control and control buttons, update the SPI FLASH software.
T.MS6M181.7A can be used in TVs:
AKAI LEA-19V07P (Panel M185B3-LC1), AKAI LEA-22V07P (Panel M215HGE-L10 Rev.C1), ERISSON 22LEE01 (Panel CLAA215FA04), FUSION FLTV-D22H11 (Panel LQ215M1LGN2), HYUNDAI H-LED19V13 (Panel CX185LEDM ), HYUNDAI H-LED15V7 (Panel N156B6-L0B Rev. C1 / Rev. C2), HYUNDAI H-LEDVD24V10 (Panel M236H3-LA2), RUBIN RB-19S2U (Panel HT185WX1-100), RUBIN RB-22S2UF (Panel LE2360A-V02), RUBIN RB-22S2UFD (Panel 22 "), RUBIN RB-24S2UFD (Panel V236H1-P01).
Main features of the FUSION FLTV-D22H11 device:
Installed matrix (LED-panel) LQ215M1LGN2.
The required supply voltage for all nodes of the TV FUSION FLTV-D22H11 provides a switching power supply.
MainBoard - the main board (motherboard) is a module T.MS6M181.7A, using CPU chips: MST6E181VS-LF-Z1; SPI Flash: 25Q32SIP; and others.The AFT7 / W130G tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: SHARP
Model: LQ215M1LGN2
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit)
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 11S3Px3x2CN WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
FUSION FLTV-D22H11 TV with LQ215M1LGN2 LCD display, diagonal size 22 "(56 cm) in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. Dynamic contrast ratio of 20,000: 1 is achieved by special control of the LEDs. The LED-panel of this TV is equipped with an end LED backlight - Edge LED. The design and technical capabilities of the TV include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in graphic standard 1080p (Full HD). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats : MP3, WMA, MPEG4, Xvid, DivX, MKV, VideoCD, SVCD, JPEG.
The power of the sound system 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB x2. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
The power consumed by the TV working in the network mode is 48 watts.
Overall dimensions: with stand 532x375x150 mm, without stand 532x344x50 mm.
TV Weight: Without Stand: 3.6 kg.
Attention! The LQ215M1LGN2 panel of the FUSION FLTV-D22H11 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
