Technical description and composition of the ROLSEN RL-17L1002U TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-17L1002U
Chassis / Version: MST6M181
Panel: LTN173KT01-A01
LED driver (backlight): 465-0103-17005G
Power Supply (PSU): Adapter K-1205
MainBoard: MST6M181-T7S 471-01A3-61702G REV A3 (2011-08-17)
IC MainBoard: Cpu: MST6M181VS-LF-Z1, SPI Flash: 25Q32BVSIG (WINBOND)
Tuner: F50CT-2DD-E (X)
Control: RC44F
ROLSEN
Model: RL-17L1002U
Chassis / Version: MST6M182
Panel: LTN173KT02 // LTN173KT01
T-CON: LTN173KT01S2LV1.4_HF
Inverter (backlight): 465-0103-17005G
Power Supply (PSU): adapter 12v 4,2a K-1205, 465-01A2-17005G
PWM Power: BM2596
MainBoard: MST6M182VG-T7S // MST6M181-T7S T7 471-01A2-61702G
IC MainBoard: IT6633E-P, 25Q32, TE330C, MP14820S, P4953W, LM1117 (3.3), BM2596-5.0
Tuner: KTDANW-14-09
RL-17L1002U Specifications
ROLSEN RL-17L1002U
General recommendations for TV LCD repair
Repair of a ROLSEN TV with a chassis should begin with a fault diagnosis, which involves a careful examination of the external and internal elements of the device. Visible damage to elements can sometimes indicate the direction of searching for a defect even before the necessary measurements are taken. If charred resistors, swollen electrolytic or sintered capacitors, ring cracks in the soldering of the terminals of transformers or heating elements are found, it is advisable to establish the causes and consequences of the malfunction, as well as check the connected elements and assemblies.
In the case when the RL-17L1002U does not turn on, does not respond to the remote control and front panel buttons, does not blink lights and does not show any signs of operability, the adapter 12v 4,2a power supply module K-1205, 465-01A2-17005G is probably faulty in this case ... If it is working properly with such manifestations, it is necessary to check the processor power regulator (converter) on the motherboard. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse in the power supply is broken, in most cases a breakdown of the power switch (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. You should also check the diodes of the rectifier bridge and the electrolytic capacitor of the mains rectifier filter.
As a rule, switches in switching power supplies (SMPS) are quite reliable and rarely fail without reasons that should be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM microcircuit is checked by replacing it with a known good one.
If the ROLSEN RL-17L1002U has no image, there is sound and the channels are switched, there is a possibility of a malfunction of the display backlight lamps or their power converter - LED driver. Sometimes, when turned on, the image appears and disappears immediately. In such cases, it is necessary to check the electrolytic capacitors of the power supply filter of the LED driver itself, including in the secondary rectifier of the main power supply unit. When disabling the protection in order to ensure the possibility of diagnosing a malfunction, special care should be taken, and after all repair work is completed, it is imperative to restore the circuits and the performance of the LED driver protection for the further safe operation of the TV.
In cases of attempts to repair the motherboard MST6M181-T7S 471-01A2-61702G, it is necessary to check the operability of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating. Complicated MB (SSB) repair is possible only in the conditions of a service center with the necessary equipment. Checking or replacing SA7454, IT6633F-P, TE330C, MP14820S, P4953W, LM1117 3.3, BM2596-5.0 elements requires the necessary training and professional skills in repairing modules at the component level. Problems associated with BGA soldering technologies can be diagnosed by the warm-up method.
Attention! Users and owners of RL-17L1002U TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting to repair themselves in order to avoid negative consequences that can lead to complete non-repairability of the device.
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-17L1002U, Main: MST6M181, Panel: LTN173KT01 A01
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-17L1002U, Main: MST6M182VG-T7S, Panel: LTN173KT02
The appearance of the MainBoard MST6M182VG-T7S is shown in the figure below:MST6M182VG-T7S can be used in TVs:
DAEWOO DSL-24L31E (Panel K236WL), ERISSON 23LEK14 (Panel 1080p Full HD 1920x1080), ERISSON 19LEK14 (Panel M185BGE-L22 Rev.C1), HYUNDAI H-LED22V5 (Panel LM215WF4), HYUNDAI H-LED24V11 (Panel LM230WF5 (TL)(D1) ), ROLSEN RL-17L1002U (Panel LTN173KT02 ), RUBIN RB-19SL1U WH (Panel 19 ").
The main features of the ROLSEN RL-17L1002U device:
Installed matrix (LCD panel) LTN173KT02 or LTN173KT01.
Matrix control uses the LTN173KT01S2LV1.4_HF Timing Controller (T-CON).
The inverter 465-0103-17005G is used to power the backlight lamps.
To power all the internal nodes of the ROLSEN RL-17L1002U TV, an external source such as adapter 12v 4,2a K-1205, 465-01A2-17005G is used using BM2596 microcircuits.
MainBoard - the main board (motherboard) is an MST6M182VG-T7S module, using the IT6633E-P, 25Q32, TE330C, MP14820S, P4953W, LM1117 (3.3), BM2596-5.0 and others.
The KTDANW-14-09 tuner provides reception of television programs and tuning to channels.
ROLSEN RL-17L1002U TV with LCD LTN173KT02, 17 "(43 cm) 16: 9. The LED panels of this TV are equipped with edge LED backlighting.It is possible to view images in high quality HD at a resolution of 1600x900 pixels in the graphic resolution 720p (HD Ready) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal shaping takes place in 480i, 480p, 576i, 576p, 720p, 1080i, 1080p standards Supported multimedia file formats: MP3, WMA, MPEG4, JPEG.
Speaker power 4 W (2x2 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV x2, S-Video, component, VGA, HDMI x2, USB. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in operating mode from the network is 25 watts.
Dimensions: 437x339x36 mm without stand.
TV weight: without stand: 2.5 kg.
Attention! Panel LTN173KT02 LED TV ROLSEN RL-17L1002U is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
