Technical description and composition of the RUBIN RB-43SE9FT2S TV, panel type and modules used. The composition of the modules.RUBIN LED
Model: RB-43SE9FT2S
Chassis / Version: CV512H-B42
Panel: CX430DLEDM
LED backlight: ZDCX43D12-ZC14F-02 303CX430032
T-CON: 6870C-0532A
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: ME15N10
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: SMK0760F
MainBoard: CV512H-B42
IC MainBoard: CPU: 9206B 1533-DBN, SPI Flash: 25Q64
Tuner: CDT-9NT372-RF01, CDT-9NS161-RD41
Control: IR: 200-GJR-LE32280-0H
Specifications RB-43SE9FT2S
RUBIN RB-43SE9FT2S
General recommendations for TV LCD LED repair
Possible malfunctions
- RUBIN RB-43SE9FT2S TV does not turn on. There are no signs of operability. The indicators on the front panel do not light up or blink, the TV does not respond to the remote control and control buttons.
In this case, first of all, you should check the operability of the main power source - the AC / DC voltage converter, all the elements of which are located on the MainBoard CV512H-B42. Its output voltages should be measured and, in their absence, the power switches (SMK0760F) and rectifier diodes should be checked for the probability of a short circuit in the converters.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the elements of the primary circuit, the mains fuse most often breaks off immediately and, less often, the current sensor in the source of the key.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements, which can disable it in key mode, or provoke an excess of the maximum current or voltage values. These can be circuits supplying the PWM controller, damper or frequency setting circuits, or OOS (negative feedback) elements in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and a short circuit between the terminals, are checked by replacing them with a known good one.
- There is no picture, but there is sound, it reacts to the remote control. Or the image appears when turned on and immediately disappears
Most likely in these cases is a malfunction of the LED panel backlight. The reason may be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
Without a special current source, it is impossible to check the line of series-connected LEDs, and it is unsafe for them to use any voltage sources over 12V for this purpose. Then all that remains is to open the panel and check each LED separately. Usually, Chinese multimeters with 9V power supply lightly light up one 3-volt LED, if you connect the probes to it in the forward direction, the red probe to the anode, and the black one to the cathode. For dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of the LED health. In the event of a malfunction of the LED, its zener diode will either be cut off, or broken through in the K / Z.
- The indicator blinks or is on constantly, the TV does not turn on, does not respond to the remote control.
If you suspect a malfunction of the tuner CDT-9NT372-RF01, CDT-9NS161-RD41, first of all, you need to make sure that the software is correct, as well as the presence of the required levels of supply voltages and pulses of data exchange with the processor via the I2C bus on the corresponding terminals of the tuner.Repair or diagnostics of the CV512H-B42 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). Complicated repair of MB (SSB) board is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements CPU: 9206B 1533-DBN, SPI Flash: 25Q64. Malfunctions in BGA chips are usually easy to detect by warm-up.
Attention! Users and owners of RB-43SE9FT2S TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting to repair themselves in order to avoid negative consequences that may lead to the complete non-repairability of the device.
DOWNLOAD SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> CV512H-B42-12
The appearance of the MainBoard CV512H-B42 is shown in the figure below:CV512H-B42
CV512H-B42 can be used in TVs:
BBK 40LEM-1010/FT2C (Panel CX390DLEDM), BBK 32LEM-1023/TS2C (Panel V320BJ6-Q01), BBK 32LEM-3035/T2C (Panel LS320TU9A00 NJ), BBK 32LEM-1036/TS2C (Panel DS32D6AP0113), BBK 42LEM-1009/FT2C (Panel T420HVN06.1 CX420DLEDM), DEXP F40B7000E (Panel V400HJ6-PE1 CX400DLEDM).
Key features of the RUBIN RB-43SE9FT2S device:
Installed matrix (LED panel) CX430DLEDM.
Matrix control uses the 6870C-0532A Timing Controller (T-CON).
To power the backlight LEDs, a converter combined with the CV512H-B42 main board is used, controlled by the BIT3267 PWM controller. The keys of the ME15N10 type are used as power elements of the LED driver.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using PWM SOT23-6 microcircuits and power switches of the SMK0760F type.
MainBoard - the main board (motherboard) is a CV512H-B42 module, using CPU: 9206B 1533-DBN chips, SPI Flash: 25Q64 and others.
The CDT-9NT372-RF01, CDT-9NS161-RD41 tuner provides reception of television programs and tuning to channels.
RUBIN RB-43SE9FT2S TV with LCD CX430DLEDM, measuring 43 "(109 cm) diagonal 16: 9. The required screen brightness of 350 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 900,000: 1 is achieved by special LED control. The technology of manufacturing the screen of this TV model is realized with LED backlighting.The design and technical capabilities of the TV provide for viewing programs and films in high quality HD at a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal shaping occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i Supported multimedia file formats: MP3, WMA, MPEG4, MKV, JPEG.
Speaker power 20 W (2x10 W) is provided by two speakers. Uses the NICAM stereo signal processing system and the Sound Surround function.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI x3, USB. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2, DVB-S2 standards.
Dimensions: with stand 968x590x178 mm, without stand 968x560x71 mm.
TV weight: with stand: 12.5 kg, without stand: 10 kg.
Attention! The CX430DLEDM panel of the RUBIN RB-43SE9FT2S LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
