Technical description and composition of the ROLSEN RL-22B01 TV, panel type and modules used. The composition of the modules.ROLSEN
Model: RL-22B01
Chassis / Version: RSAG7.820.1653 VER.A
Panel: LTM220M1-L01 SD
Inverter (backlight): JSI-220402 P / N: 47131.220.0 / 0112805
PWM Inverter: TL494C
MOSFET Inverter: AOD484, AOD417
Power Supply (PSU): JSI-220402 P / N: 47131.220.0 / 0112805
PWM Power: LD7575PS (PWM flyback)
MainBoard: RSAG7.820.1653 VER.A
IC MainBoard: AZ1084S 3.3E1, Z1015AI, Z1021AI, K24C32, 4558CM-E1, HS9453, CD1517CP, TDA9886TS, ME4953
Tuner: TDQ-6FT / W126HR0H
Control: EN-21610
RL-22B01 Specifications
ROLSEN RL-22B01
General recommendations for TV LCD repair
Repair of a ROLSEN TV with RSAG7.820.1653 VER.A chassis should begin with a careful external examination of all its constituent elements and modules. Often, based on external signs and the nature of damage to elements, it becomes possible to draw some conclusions and determine a further algorithm for searching for a defect before taking the necessary measurements at control points. Experienced repairmen often guess about the causes of the defect and the possible consequences, for example, by ring cracks in the soldering of the element terminals, as well as by swollen capacitors or resistors burnt out to coal dust and other external indirect signs.
Malfunctions of the power supply module JSI-220402 P / N: 47131.220.0 / 0112805 can be expressed in different ways, for example, the ROLSEN RL-22B01 does not turn on at all and the control lamps on its front panel do not light up or blink, all signs of operability are absent. It should be noted that the processor power regulator (converter) may be faulty with the same external manifestations. When diagnosing and repairing the power supply, after replacing the swollen capacitors of the secondary rectifier filters (if any), you must first check the mains fuse. If it is broken, the power elements of the transistors BA8B4S, BA9A1S and the rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
Power switches in switching power supplies (SMPS) fail for no reason very rarely and, if they break down, it is necessary to look for a malfunction in the stabilization circuits, checking electrolytic capacitors, semiconductor devices and resistors in the primary circuit. The reason may be a malfunction of the LD7575PS PWM regulator microcircuit, which can only be verified by replacing it with a new or known good one.
If, when turning on the TV, the image appears and immediately disappears, or is absent initially when turned on, but there is sound and other functions work, there is a high probability of a malfunction of the inverter (backlight power converter). In such cases, the lamps, the inverter and the common power supply module must be checked, in which the electrolytic capacitors of the rectifier filter supplying the inverter must be checked. It should be remembered that when the protection is turned off in order to diagnose a malfunction, there is always a risk of failure of the power elements of the inverter. After repair, it is imperative to restore all standard converter protection circuits.
The RSAG7.820.1653 VER.A motherboard must be checked if there is no reaction to the remote control and function buttons, the standby indicator blinks or is on continuously. In such cases, if the converters or power regulators of the microcircuits are working, it may be necessary to update the software. In cases of complex MB (SSB) repairs and with the necessary skills and equipment, it may sometimes be necessary to replace its AZ1084S 3.3E1, Z1015AI, Z1021AI, K24C32, 4558CM-E1, HS9453, CD1517CP, TDA9886TS, ME4953 and other possible faulty components. Malfunctions associated with the use of BGA soldering technologies are usually easily diagnosed by the warm-up method.
Owners and users of the ROLSEN RL-22B01 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-22B01, Main: RSAG7.820.1653 VER.A, Panel: LTM220M1-L01 SD
The appearance of the MainBoard T.VST29.A2B_12313 is shown in the figure below:T.VST29.A2B_12313
T.VST29.A2B_12313 can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
The main features of the ROLSEN RL-22B01 device:
Installed matrix (LCD panel) LTM220M1-L01 SD.
The JSI-220402 inverter is used to power the backlight lamps, it is controlled by the TL494C PWM controller. The keys of the AOD484, AOD417 types are used as power elements of the inverter.
The formation of the necessary supply voltages for all nodes of the ROLSEN RL-22B01 TV is carried out by the JSI-220402 power module, or its analogs using LD7575PS microcircuits (PWM flyback).
MainBoard - the main board (motherboard) is an RSAG7.820.1653 module, using chips AZ1084S 3.3E1, Z1015AI, Z1021AI, K24C32, 4558CM-E1, HS9453, CD1517CP, TDA9886TS, ME4953 and others.
The TDQ-6FT / W126HR0H tuner provides reception of television programs and tuning to channels.
Information from an alternative source:
TV ROLSEN RL-22B01
Panel type (matrix): LTM220M1-L01 SD
Motherboard: RSAG7.820.1653 VER.A, AZ1084S 3.3E1, Z1015AI, Z1021AI, F40-100GCP, K24C32, 4558CM-E1, HS9453, ATMLH912 04B-1, CD1517CP, TDA9886TS, ME4953, SAW: HS9453 & HS6257, Tuner: TDQ-6FT/W126H\R0H, PSU & INVERTER: JSI-220402 P/N:47131.220.0/0112805, TL494C, BA8B4S x2, BA9A1S x2, LD7575PS
Remote control: EN-21610
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTM220M1-L01
Type: a-Si TFT-LCD, Panel
Diagonal size: 22.0 inch
Resolution: 1680x1050, WSXGA +
Display Mode: TN, Normally White, Transmissive
Active Area: 473.76x296.1 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 1.3 / 3.7 (Tr / Td)
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
ROLSEN RL-22B01 TV with LCD display LTM220M1-L01, 22 "(55 cm) diagonal, 16:10 format. Screen brightness of 300 cd / m² is backlit by CCFL (EEFL) fluorescent lamps. Dynamic contrast ratio of 8000: 1 is provided by a special control of the backlight depending on the illumination of areas in the scene.It is possible to view images in high quality HD at a resolution of 1680x1050 pixels in the standard graphic resolution 720p (HD Ready) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. and the digital signal is generated in the 480i, 480p, 576i, 576p, 720p, 1080i standards.
Speaker power 4 W (2x2 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x3, S-Video, component, VGA, HDMI. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
TV weight: 6 kg.
Attention! The LTM220M1-L01 SD panel of the ROLSEN RL-22B01 LCD TV is the most expensive component.
Avoid hitting the glass and putting pressure on the screen surface to avoid irreversible damage to the LCD panel!
