Technical description and composition of the ROLSEN RL-19L1003U TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-19L1003U
Chassis / Version: T.VST29.A2B
Panel: M185BGE-L10 Rev. C1
LED driver (backlight): AY039D-1SF02 Rev1.0
Power Supply (PSU): AY039D-1SF02 Rev1.0
MainBoard: T.VST29.A2B_12313
IC MainBoard: PCU: TSUMV59XE-Z1
RL-19L1003U Specifications
ROLSEN RL-19L1003U
General recommendations for TV LCD LED repair
Repair of the ROLSEN RL-19L1003U TV should begin with a careful external examination of all its constituent elements and modules. It often happens that visible damage to elements or connections helps determine the direction of troubleshooting. In some cases, defective elements are visible with the naked eye, for example, charred resistors or swollen sintered capacitors, or electrolytic ones in rectifier filters. The formed ring cracks in the soldering of the terminals of transformers or heating circuit elements are also frequent sources of many malfunctions with a variety of external manifestations.
In the case when the RL-19L1003U does not turn on, does not respond to the remote control and front panel buttons, does not blink lights and does not show any signs of operability, the AY039D-1SF02 Rev1.0 power supply module is probably faulty in this case. If it is working properly with such manifestations, it is necessary to check the processor power regulator (converter) on the motherboard.In the absence of swollen capacitors of the secondary rectifier filter, the power supply should be diagnosed by checking the fuse and, if it is broken, it is necessary to first check all power semiconductor elements primary circuit - diodes and transistors for the probability of avalanche or thermal breakdown.
Power switches in switching power supplies (SMPS) fail for no reason very rarely and, in case of their breakdown, it is necessary to look for a malfunction in the stabilization circuits, checking electrolytic capacitors, semiconductor devices and resistors in the primary circuit. The reason may be a malfunction of the PWM regulator microcircuit, which can only be checked by replacing it with a new or known good one.
If, when the TV is turned on, the image appears and immediately disappears, or is absent initially when turned on, but there is sound and other functions work, there is a high probability of a malfunction of the LED driver (the power converter for the LEDs of the panel backlight M185BGE-L10 Rev. C1). In such cases, the general power module is also subject to verification, in which the electrolytic capacitors of the rectifier filter supplying the LED driver should be checked.
In most cases of lack of backlighting, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or more LEDs do not work in one line, then they are broken and should be replaced.
It should be remembered that it is not possible to determine an open circuit in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
Repair of the motherboard T.VST29.A2B 12313 must begin with diagnostics and testing of all linear stabilizers or power converters of its microcircuits. Sometimes it may be necessary to update the software (software) - flashing FLASH or EEPROM.
In some cases, the elements of the MB (SSB) board - PCU: TSUMV59XE-Z1 require checking or replacing (if necessary). In cases where a BGA processor is used, its malfunction is usually detected by the local warm-up method.
Owners of the RL-19L1003U TV are advised to contact only qualified specialists with experience for repair! Attempts to repair yourself without the appropriate knowledge and skills can lead to serious negative consequences!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-19L1003U, Main: T.VST29.A2B 12313, Panel: M185BGE-L10 Rev.C1
The appearance of the MainBoard T.VST29.A2B_12313 is shown in the figure below:T.VST29.A2B_12313
T.VST29.A2B_12313 can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
The main features of the ROLSEN RL-19L1003U device:
Installed matrix (LED-panel) M185BGE-L10 Rev. C1.
AY039D-1SF02 LED driver is used to power the backlight LEDs.
The formation of the necessary supply voltages for all nodes of the ROLSEN RL-19L1003U TV is carried out by the AY039D-1SF02 power module, or its analogs.
MainBoard - the main board (motherboard) is a T.VST29.A2B_12313 module, using PCU chips: TSUMV59XE-Z1 and others.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: M185BGE-L10
Type: a-Si TFT-LCD, Panel
Diagonal size: 18.5 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 409.8x230.4 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 200 cd / m²
Contrast Ratio: 700: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 4 strings WLED Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 5.0V
ROLSEN RL-19L1003U TV with LCD M185BGE-L10, diagonal 19 "(48 cm) in 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 100,000: 1 is achieved by special control of LED operation The LED panel of this TV is equipped with edge LED backlighting.It is possible to view images in high quality HD at a resolution of 1366x768 pixels in a graphic resolution of 720p (HD Ready) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM , NTSC Graphic processing and digital signal shaping takes place in 480i, 480p, 576i, 576p, 720p, 1080i standards Supported multimedia file formats: MP3, WMA, MPEG4, MKV, JPEG.
Speaker power of 6 W (2x3 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI, USB. A headphone output is provided. To connect a computer or laptop to this TV model, use the VGA (D-Sub 15) connector on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in operating mode from the network is 40 watts.
TV weight: 3.6 kg.
Attention! The panel M185BGE-L10 Rev. C1 of the ROLSEN RL-19L1003U LED TV is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.
