Technical description and composition of the TV SONY KD-49X8005C, type of panel and modules used. Module composition.
Composition Specifications
SONY KD-49X8005C
Smart TV UHD KD-49X8005C | Year of manufacture: 2015
Screen diagonal: 49" (124 cm)
Display format: 16:9
Resolution: 3840x2160
Refresh rate: 50 Hz
LCD panel type: LC490EQY-SHM2/SYV4942
LED backlight: Yes
Smart: yes. Wi-Fi support: yes
Operating system: Android
Support HD: 4K UHD
Viewing angle: 178°
Progressive scan: Yes
TV standards: PAL, SECAM, NTSC
Digital tuner: DVB-T, DVB-T2, DVB-C, DVB-S, DVB-S2
Teletext: Yes
DTV formats: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, 2160p
Multimedia: MP3, WMA, MPEG4, JPEG
Stereo sound: there is
Sound power: 20W (2x10W)
Acoustics: two speakers
Interface: AV, component, SCART, HDMI x4, MHL, USB x3, Ethernet (RJ-45), Bluetooth, Wi-Fi 802.11n, Miracast
Headphone jack: yes
TV weight: with stand: 14.3 kg
Without stand: 13.2 kg
Dimensions: with stand 1107x691x246mm
without stand 1107x651x80mm
AC Consumption: 187W
SONY LED
Model: KD-49X8005C
Panel: LC490EQY-SHM2 // SYV4942
LED backlight: SUY490A23_Rev00_5LED_L/R_150223
T-CON: 6870C-0573A
LED driver (backlight): integrated into PSU
PWM LED driver: BD9423EFV
MOSFET LED driver: TO-220
Power Supply (PSU): 1-980-310-11 APS-395
PWM Power: MIP2H2 (STB)
MainBoard: 1-894-595-11 // 1-894-595-12
IC MainBoard: IMAGE: MT5830DEHJ-BHHAH, CXD4753GB, eMMC: KLMAG2GEND-B031, Audio: : TAS5760M
Tube: CE541ZP
General advice about LCD LED TV repair
Possible problems
- SONY KD-49X8005C does not turn on, the indicators on the front panel do not light or blink. TV does not respond to the remote control.
It is most likely that the main switching power supply (MPS) 1-980-310-11 is faulty. You should measure its output voltages and in case of their absence, check the serviceability of the power switches and rectifier diodes in converters for possible breakdown.
At breakdown of semiconductors in the secondary circuits of any converter, as a rule, it can work in the emergency short-circuit mode without output voltages, and at short circuit in the elements of the primary circuit most often immediately burst the mains fuse and less often the current sensor at the source of the key.
Breakdown of Mos-Fet switches, used in pulse sources, is often caused by failure of other elements, for example, in PWM regulator supply circuit, in frequency-retaining or damping circuits, as well as in the Negative Feedback Stabilization. PWM MIP2H2 (STB) chips are usually checked by replacing them with new or known good ones.
- No picture, screen is black, there is sound, with external screen illumination sometimes you can see faint outlines of the image.
In such cases, the most likely faulty elements of the LED panel backlight. More often the reason for this is a breakage of LEDs, or poor contact in the connectors of strips, less often faulty can be the LED-driver.
Without a special current source to check the line of LEDs in series is impossible, and to use for this purpose, any voltage sources over 12v is not safe for them. Then you only have to open the panel and check each LED separately. Usually Chinese multimeters with 9V power supply will light up one 3 volt LED a bit if you connect the probes to it in forward direction, red probe to anode, black probe to cathode. For twin 6-volt LEDs, the PN junction of its faulty regulator can be used as an indicator of the health of the LED. If the LED is faulty, it will either be open or shorted.
- The TV set does not enter the operation mode, the remote control does not respond. Front panel LED is either constantly on or is blinking.
In cases where the SONY KD-49X8005C has no picture but sound, often the display backlight does not work.
In LED-TVs are usually faulty LEDs inside the panel LC490EQY-SHM2, and less often the LED-driver.
Without backlighting, you can sometimes see a faintly visible image with a certain luck of external lighting on the screen.
Replacing the LEDs requires disassembly of the LC490EQY-SHM2. Such work is not recommended for TV owners and craftsmen who do not have experience in repairing LCD-panels on their own, especially at home.
READ HOW TO REPAIR THE TV LED BACKLIGHT --------------> HERE.
If there is no image, but backlighting works, the screen becomes a little lighter when the TV is switched on, and the open TV can see the light through the holes in the panel body.
If this is the case the T-CON (Timing Controller) board may be faulty, but often the MainBoard 1-894-595-11 is faulty as well. Software failure is also possible. The MainBoard may also be malfunctioning due to damage to keypads or stub cables, such as after getting wet. In such cases, first of all check the panel power supply voltage at the LVDS connector, fuses on the T-CON board or panel strips, as well as supply and reference voltages for column and line drivers - VGH, VGL, Vcom.
If they are within normal limits, then an oscilloscope must be used to monitor the LVDS signals from the MainBoard 1-894-595-11, as well as synchronizing signals to the driver stubs.
Flooded LED TV screens can sometimes be repaired if there is no significant damage to the cables or panel strips.
Repair or diagnosis of motherboard 1-894-595-11 should be started with checking stabilizers and power converters necessary to power the chips and matrix. If necessary, software (software) should be updated or replaced. Complex repair of MB (SSB) is possible only in the conditions of the service center with the necessary equipment. Check or replacement of the elements IMAGE: MT5830DEHJ-BHHAH, CXD4753GB, eMMC: KLMAG2GEND-B031, Audio: : TAS5760M requires the necessary training and professional skills to repair the modules at the component level. Problems using BGA soldering techniques can sometimes be diagnosed by heating.
Before replacing your CE541ZP tuner, if you cannot tune to the TV channels, make sure that you have a supply voltage, which should be measured on the corresponding pins of the tuner and the software should be checked for correctness. The tuner-to-processor communication pulses can be checked with an oscilloscope
Warning to the users! Unauthorized repair of your SONY KD-49X8005C TV without necessary skills and experience can lead to its total unrepairability!
More on MainBoard Repair
An exterior view of the MainBoard 1-894-595-11 is shown in the illustration below:
1-894-595-11
Appearance of the power supply
1-980-310-11:
1-980-310-11
The main features of the SONY KD-49X8005C device:
A matrix (LED panel) LC490EQY-SHM2 or SYV4942 is installed.
A Timing Controller (T-CON) 6870C-0573A is used to control the matrix.
A converter combined with a power supply is used to power the LED backlight and is controlled by a BD9423EFV PWM controller. The TO-220 type switches are used as power elements of LED-driver.
Forming the necessary supply voltages for all components of the TV SONY KD-49X8005C is performed by a power module 1-980-310-11 or its analogues using MIP2H2 (STB) chips.
MainBoard - the main board (motherboard) is 1-894-595-11 module, using IMAGE: MT5830DEHJ-BHAH, CXD4753GB, eMMC: KLMAG2GEND-B031, Audio: TAS5760M and others.
The CE541ZP tuner allows you to receive TV programs and tune in to channels.
Instructions and updates:
Update firmware to version 5.435:
File sony_tvupdate_2015_5435_eub_auth.zip, version 5.435 of 26.06.2019 (1,644,778,348 bytes).
For models: KD-75XD9405, KD-65XD9305, KD-55XD9305, KD-85XD8505, KD-75XD8505, KD-65XD8505, KD-65XD8577, KD-65XD8599, KD-55XD8505, KD-55XD8577, KD-55XD8588, KD-55XD8599, KD-65SD8505, KD-55SD8505, KD-75X9405C, KD-65X9305C, KD-55X9305C, KD-75X9105C, KD-65X9005C, KD-55X9005C, KD-75X8501C, KD-75X8505C, KD-65X8501C, KD-65X8505C KD-65X8507C, KD-65X8508C, KD-65X8509C, KD-55X8501C, KD-55X8505C, KD-55X8507C, KD-55X8508C, KD-55X8509C, KD-49X8301C, KD-49X8305C, KD-49X8307C, KD-49X8308C KD-49X8309C, KD-43X8301C, KD-43X8305C, KD-43X8307C, KD-43X8308C, KD-43X8309C, KD-55X8005C, KD-49X8005C, KD-65S8505C, KD-55S8505C, KD-65S8005C, KD-55S8005C.
The update file and instructions can be downloaded from the manufacturer's website for the KD-49X8005C model.
Benefits and improvements of the latest update:
The latest Android security updates.
Manuals and instructions are also available for this model:
Reference Manual (Web Manual). Published 22 Jul 2019.
Reference Guide (Web Manual). Published 22 Feb 2017.
Wall-Mount Bracket. Published 15 Dec 2015, size 10.43 MB.
Quick set up guide and quick start guide. Published 18 Aug 2015, size 2.62 MB.
SONY KD-49X8005C TV with LC490EQY-SHM2 LCD display, measuring 49" diagonally (124 cm) format 16:9. In the manufacturing technology of the display of this model is implemented LED backlight.
LC490EQY-SHM2 matrix and MainBoard software 1-894-595-12 able to realize the image in the highest quality UHD at 3840x2160 pixels in 4K UHD standard.
The KD-49X8005C has built-in SMART Software and pre-installed Android Operating System. Internet connection can be made via Wi-Fi wireless connection. Input analog video signal can be processed in PAL, SECAM, NTSC systems. Graphical processing and picture formation of the digital signal is carried out in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, 2160p. Video processor supported multimedia file formats: MP3, WMA, MPEG4, JPEG.
The capacity of the sound system is 20 W (2x10 W) provides two speakers. NICAM stereo signal processing system and Sound Surround surround sound function are used.
External interface (connection to other devices) is supported by standard inputs and outputs: antenna input (RF), AV, component, SCART, HDMI x4, MHL, USB x3, Ethernet (RJ-45), Bluetooth, Wi-Fi 802.11n, Miracast. There is a headphone output. To connect an analog computer or laptop to this TV model uses a VGA (D-Sub 15) connector that supports 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080, 3840x2160. The digital tuner is capable of receiving DVB-T, DVB-T2, DVB-C, DVB-S, DVB-S2 TV channels.
The power consumed by the worker in mains mode is 187 W. Power supply APS-395.
Overall dimensions: with stand 1107x691x246 mm, without stand 1107x651x80 mm.
TV weight: with stand 14.3 kg, without stand 13.2 kg.
Warning. The LC490EQY-SHM2 is the most expensive part of your SONY KD-49X8005C LED TV.
Avoid hitting the glass and excessive pressure on the surface of the screen to avoid damage to the LED panel!
It is not safe to get any liquid on the screen. Sometimes a single drop of water is enough, if it drips down the glass onto the stubs, the TV may become unrepairable.
