PANASONIC TX-LR50B6 Service Mode - Led blinking code - self diagnostics – LED Television Repair and Service
Category: LED Television Repair And Service
Contents of this article
- How to access to service mode
- LED blinking codes
- Self Check Mode
- Voltage Check
PANASONIC TX-LR50B6
Service Mode
How to enter into Service Modes
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
How to enter into Service Modes
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
How to exit Service mode
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
Exit
1. Disconnect the AC cord from wall outlet.
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
Exit
1. Disconnect the AC cord from wall outlet.
Self Check Mode
1. Press the ‘MENU’ button (on the remote control) and the ‘VOL DOWN’ button on the LCD panel.
2. Press ON/OFF button on the panel to Exit.
1. Press the ‘MENU’ button (on the remote control) and the ‘VOL DOWN’ button on the LCD panel.
2. Press ON/OFF button on the panel to Exit.
Hotel Mode Adjustment
1. Press the ‘VOLUME DOWN’ button on the TV panel and simultaneously press the INPUT button on the remote control 3 times to enter Hotel Mode.
2. Set Hotel mode ‘on/off’, then press ‘EXIT’ to come out.
Hotel Mode
1. Press the ‘VOLUME DOWN’ button on the TV panel and simultaneously press the INPUT button on the remote control 3 times to enter Hotel Mode.
2. Set Hotel mode ‘on/off’, then press ‘EXIT’ to come out.
Hotel Mode
Access command to the Hotel mode setup menu. In order to display the Hotel
mode setup menu, please enter the following command (within 2 second). [TV]
: Vol [Down] [REMOTE] : INPUT (3 times). To exit the Hotel mode setup menu Disconnect
AC power cord from wall outlet.
Check of the IIC bus lines
How to access
Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
Exit
Disconnect the AC cord from wall outlet.
How to access
Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
Exit
Disconnect the AC cord from wall outlet.
Power LED Blinking
When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit as follow:
When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit as follow:
|
LED Blink
|
SOS detection
|
|
1
|
BL_SOS
|
|
7
|
SUB_3.3V
|
|
9
|
SOUND_SOS
|
|
8
|
OVP
SOS
|
|
10
|
GCX/FRC_SOS
|
|
12
|
BE(sLD8/PRO4)
SOS
|
|
13
|
Emergency
SOS
|
|
3
|
IROM-SOS
|
Measurements and Adjustments
Voltage chart of A-board
Set A-Board to a dummy set and check the satisfaction with the specified voltage as following table.
Set A-Board to a dummy set and check the satisfaction with the specified voltage as following table.
|
Power Supply Name
|
Measurement Poin
|
Specification
|
|
PNL12V
|
TP4097
|
12.1
± 0.8V
|
|
SUB3.3V
|
TP5400
|
3.32
± 0.165V
|
|
SUB1.1V
|
TP8101
|
1.14
± 0.07V
|
|
SUB1.5V
|
TP8100
|
1.52
± 0.05V
|
|
SUB5V
|
TP5420
|
5.0
± 0.25V
|
|
HDMI3.3V
|
TP8000
|
3.3
± 0.16V
|
Voltage chart of P-board
Set P-Board to a dummy load and check the satisfaction with the specified
voltage as following table.
|
Output
|
Test Point
|
Step 1
|
Step 2
|
|
24V
(PANEL)
|
TP7407
or TP7408
|
<1V
|
24 ±
1.2V
|
|
16V
|
TP7410
or TP7412
|
<1V
|
15.7
± 0.6V
|
|
5VS
|
TP7501
|
5.3
± 0.2 V
|
5.3
± 0.2V
|
|
PFC
|
TP7201
|
<340V
|
390
± 15V
|
