REPAIRING AND NOT THROWING AWAY

REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:
- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Thursday, 28 March 2019

TOSHIBA 19DV616DG 22DV616DG LCD TV/DVD COMBINATION – HOW TO ENTER SERVICE MODE – HOTEL MODE – PARENTAL CONTROL CANCELLATION – SOFTWARE UPDATE –

TOSHIBA 19DV616DG 22DV616DG LCD TV/DVD COMBINATION – HOW TO ENTER SERVICE MODE – HOTEL MODE – PARENTAL CONTROL CANCELLATION – SOFTWARE UPDATE – 

How to take out disc in emergency – How to enter Service Mode – Replacing the EEPROM IC and adjustments – Unlock the parental control password -  Power Supply Circuit Diagram - TOSHIBA 19V616 - TOSHIBA 22DV616 LCD TVA- LCD TV-DVD Combination.
SMPS CIRCUIT: USED ICs - KIA431A-AT (Voltage regulator) _ MP1580HP _ FA5571N-D1 (Power Control)
DISC REMOVAL METHOD AT NO POWER SUPPLY - (Disc removal at Emergency)
1. Remove the Stand, Front Cabinet Ass'y and LCD Panel.
2. Slide the Gear Middle toward the arrow direction by hand to release the lock.
3. Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.
PARENTAL CONTROL - RATING LEVEL & 4 DIGIT PASSWORD CANCELLATION.
FOR DVD MODE
If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below.
1. Turn Unit ON.
2. Set the DVD to the Stop Mode.
3. Check that “No disc” is displayed on the screen.
4. Press and hold the “STOP” button on the front panel.
5. Simultaneously press and hold the “7” key on the remote control unit.
6. Hold both keys for more than 2 seconds.
7. The On Screen Display message “PASSWORD CLEAR” will appear.
8. The 4 digit password has now been cleared.
FOR DTV MODE
If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below.
1. Turn on the power.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (3) on the remote control for more than 2 seconds.
4. The 4 digit password has now been cancelled. [NOTE: No indications on the screen when the Parental Lock is setting.  Initializing password is 0000.]
HOTEL MODE FUNCTION
In power on mode, set the VOLUME to minimum.
> Press and hold the VOLUME DOWN button on the side panel.
> Simultaneously press and hold the channel button (7) on the remote control for more than 2 seconds.
> The Hotel mode setting menu will appear.
> Using the UP/DOWN button on the remote control, select the desired mode. Then press the ENTER button.
> Using the LEFT/RIGHT button on the remote control, set the mode to desired setting.
The Hotel mode has now been set up.
To Re-set the Hotel mode
1. In power on mode, set the VOLUME to minimum.
2. Press and hold the VOLUME DOWN button on the side panel.
3. Simultaneously press and hold the channel button (7) on the remote control for more than 2 seconds.
4. The Hotel mode setting menu will appear.
5. Using the UP/DOWN button on the remote control, select the RESET.  Then press the ENTER button.
6. The setting items have now been returned to initial value.
Note-1 Even if setting it to "No Respond", the service mode function are effective.  Note 2 - If setting it to "OFF", it start up in same input source when you turn off the power before.
TRAY LOCK
The disk cannot be taken out by setting the Tray Lock, please follow the steps below.
1. Turn Unit ON.
2. Set the DVD to the Stop Mode.
3. Press it in order of "SEPUP", "SUBTITLE", "3", "AUDIO SELECT" and "0" key of a remote control unit.
4. The On Screen Display message will appear.
5. The Tray Lock has now been set up.
To unlock the Tray Lock, please follow the steps below.
1. Turn Unit ON.
2. Set the DVD to the Stop Mode.
3. Press it in order of "SETUP", "SUBTITLE", "3", "AUDIO SELECT" and "0" key of a remote control unit.
4. The On Screen Display message will appear.
5. The Tray Lock has now been cleared.
Power circuit
SERVICE MODE LIST
To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.
Press the following remocon keys continuously.
SETUP > SUBTITLE > 3 > AUDIO SELECT > 0
The disk cannot be taken out. [Refer to the "TRAY LOCK".]
RE-WRITE FOR DVD FIRMWARE
>Turn on the power, and set the DVD mode.
> Confirm that the "No Disc" will be appeared on the screen.
> Press both VOL. DOWN button on the set and Channel button (5) on the remote control for more than 2 seconds.
> Press VOL. UP/DOWN button on the unit to check if all the keys on the unit do not function.  NOTE: To check if DVD Write mode is set.  When inserting Up-Date Disc at Non DVD Write mode, the read error will happen.
> Insert the Up-Date Disc. (Refer to SERVICING FIXTURE AND TOOLS)
> Automatic read will start and "Firmware upgrade Please Wait" will be displayed on the screen.  At this time, the horizontal noise lines may appear. But no problem.  NOTE: Do not turn off the unit on the way or operate the keys on the unit and remocon.  Up-Date error will happen and cannot be done with the Up-Date of Up-Date Disc.
> Unplug the AC cord, then plug it in.  After the write, set to the initializing of shipping.
> Turn on the power, and set the DVD mode.
> Press both VOL. DOWN button on the set and Channel button (4) on the remote control for more than 2 seconds.
The "INITIALIZE 5 > COMPLETE" will appear on the screen.  Then unplug the AC cord, and plug it in.
CHECK FOR THE FIRMWARE VERSION
> Turn on the power, and set the DVD mode.
> Press both Channel button (1) on the remote control and the STOP button on the set for more than 2 seconds.  Firmware version will be displayed on the top left of the screen.
When the changed version displays, the Re-write will be completed. 
>Turn off the power.
WHEN REPLACING EEPROM (MEMORY) IC
Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. Total hours are displayed in 16 system of notation.
If you set a factory initialization, the total hours is reset to "0".  Refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
1. Turn on the POWER, and set to the ALL mode.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
4. After the confirmation of each check sum, turn off the power.  NOTE: The each item value might be different according to each set.
CONFIRMATION OF INITIAL DATA
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be
taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
1. Turn on the POWER, and set to the ALL mode.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.  ADDRESS and DATA should appear as FIG.  NOTE: No need to set data other position than 0D00~0E3F and 1000~7FFF.
4. ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS until required ADDRESS to be changed is reached.
5. Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
7. Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
8. Repeat steps 4 to 6 until all data has been checked.
9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.  After the data input, set to the initializing of shipping.
10. Turn on the Power.
11. Set the VOLUME to minimum.
12. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
13. After the finishing of the initializing of shipping, the unit will turn off automatically.  The unit will now have the correct DATA for the new MEMORY IC.
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION
Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. Total hours are
displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".  Refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding
1. Turn on the POWER, and set to the ALL mode.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
4. After the confirmation of each check sum, turn off the power.  NOTE: The each item value might be different according to each set.  If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
1. Turn on the POWER, and set to the ALL mode.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.  ADDRESS and DATA should appear.  NOTE: No need to set data other position than 0D00~0E3F and 1000~7FFF.
4. ADDRESS is now selected and should "blink". Using the UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached.
5. Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
7. Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
8. Repeat steps 4 to 6 until all data has been checked.
9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.  After the data input, set to the initializing of shipping.
10. Turn on the Power.
11. Set the VOLUME to minimum.
12. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
13. After the finishing of the initializing of shipping, the unit will turn off automatically.  The unit will now have the correct DATA for the new MEMORY IC.



CLICK ON THE PICTURES TO MAGNIFY
Posted By: FRANK at 06:17
TAG: , , , , , , ,