LG
Model: 32LG10R
Chassis / Version: LP81A
Panel: T315XW02 V.L
Lamp backlight: CCFL
Inverter (backlight): 4H.V2668.001
PWM Inverter: OZ964SN, BA2902F, N5100V
MOSFET Inverter: APM4015P, APM4010N
Power Supply (PSU): EAY4050440 LGP32-08H
PWM Power: G6961 (PFC), NCP1396AD, NCP1207AD
MainBoard: EAX40043810 (3)
IC MainBoard: LGE6991DD-LF, AT24C64, 25Q16, NTP3000A
Tuner: TAFT-H703F
Specifications 52LG5030
LG 32LG10R
General recommendations for repairing TV LCD
Possible malfunctions
- LG 32LG10R does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In some of these cases, a fault is detected in the EAY4050440 power module. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches of the converters and rectifier diodes for the probability of a short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key are most often cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) G6961 (PFC), NCP1396AD, NCP1207AD, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
These manifestations can be triggered by a power module, or by defects in the inverter, as well as a distortion of the currents in the lamps due to their uneven wear. After checking all the electrolytic capacitors of the filters that are involved in the power supply of the inverter, it is necessary to ring in its converter the power switches for breakdown and the secondary windings of the transformers for an open.
If in diagnosing a malfunction, it is necessary to disable the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during work, and after their completion, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the EAX40043810 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips LGE6991DD-LF, AT24C64, 25Q16, NTP3000A and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before replacing the TAFT-H703F tuner, if there is no tuning to the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Owners and users of the LG 32LG10R TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
Service manual and schematic diagram LG 32LG10R Chassis LP81A
The appearance of the MainBoard EAX40043810 is shown in the figure below:
EAX40043810
The appearance of the power supply
Main features of the device LG 32LG10R:
Installed matrix (LCD panel) T315XW02 V.L.
To power the backlight, an inverter 4H.V2668.001 is used, it is controlled by the PWM controller OZ964SN, BA2902F, N5100V. As power elements of the inverter, keys of the type APM4015P, APM4010N are used.
The necessary supply voltages for all nodes of the LG 32LG10R TV are generated by the EAY4050440 power module or its analogs using G6961 (PFC), NCP1396AD, NCP1207AD microcircuits.
MainBoard - the main board (motherboard) is an EAX40043810 module using LGE6991DD-LF, AT24C64, 25Q16, NTP3000A and other chips.
The TAFT-H703F tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: AUO
Model: T315XW02 VL
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: AMVA, Normally Black, Transmissive
Active Area: 697.68x392.26 mm
Surface: Antiglare (Haze 11%), Hard coating (3H)
Brightness: 450 cd / m²
Contrast Ratio: 2500: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 6.5 (G to G)
Frequency: 60Hz
Lamp Type: CCFL Embedded (Inverter)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V