Technical description and composition of the LG 42LB580V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LB580V
Chassis / Version: LE46 / LD46
Panel: LC420DUE (FG) (A4)
LED backlight: 6916L-1709A, 6916L-1710A
T-CON: 6870C-0480A
LED driver (backlight): integrated into PSU
PWM LED driver: BD9486F
MOSFET LED driver: 4NF20, MDD3752
Power Supply (PSU): EAX65423701 (2.0) LGP3942-14PL1 PLDF-L307A
PWM Power: MAP8800, FA6A01N, NR134S
MOSFET Power: TK7P60W
MainBoard: EAX65610904 (1.0) EBR78668701 EBT63297701
IC MainBoard: H5TQ4G63AFR, EEPROM: 24C256, SOUND: Audio: NTP7513
Tuner: EBL61400501 TDJM-G101D
Control: Remote: AKB73715679, IR: EBR78480601, WIFI: TWFM-B006D EAT61813901
Specifications 42LB580V
LG 42LB580V
General repair guidelines for TV LCD LED
Possible malfunctions
- LG 42LB580V does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In such cases, the EAX65423701 power supply is usually faulty. It is necessary to measure its output voltages, and in case of their absence, check the operability of the power switches (TK7P60W) of the converters and rectifier diodes for a short circuit probability.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM chips MAP8800, FA6A01N, NR134S are usually checked by replacing with new ones, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
Often in such cases, there is no LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the EAX65610904 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of attempts to repair the MB board (SSB), it is necessary to check the health of its elements - H5TQ4G63AFR, EEPROM: 24C256, SOUND: Audio: NTP7513 which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
Before changing the tuner EBL61400501 TDJM-G101D, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding tuner pins and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Attention TV owners! Attempts at self-repair of LG 42LB580V are not recommended by the manufacturer and can lead to serious negative consequences!
Schematic diagram ------------> LG 42LB58* Chassis LE46/LD46 .
42LB58**, 42LB58**-Z*, 42LB580V, 42LB580V-TA
The appearance of the MainBoard EAX65610904 is shown in the figure below:EAX65610904
EAX65610904 can be used in TVs:
LG 32LB582V ZG (Panel LC320DUE (FG)(A4)), LG 42LB570V (Panel LC420DUE (FG)(A4)), LG 42LB5800 (Panel LC420DUE (P6)(A4)), LG 42LB580V (Panel LC420DUE (FG)(A4)), LG 32LB570U 32LB570U-ZJ (Panel NC320DXN VSBP2), LG 39LB580V (Panel T390HVF02.0 HC390DUN-VCHS1), LG 32LB580V ZB (Panel LC320DUE (FG)(A4)).
The appearance of the power supply
Main features of the device LG 42LB580V:
Installed matrix (LED-panel) LC420DUE (FG) (A4).
The matrix control uses the Timing Controller (T-CON) 6870C-0480A.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the BD9486F PWM controller. As power elements of the LED driver, keys of the type 4NF20, MDD3752 are used.
The necessary supply voltages for all nodes of the LG 42LB580V TV are generated by the EAX65423701 power supply module or its analogs using MAP8800, FA6A01N, NR134S microchips and TK7P60W power switches.
MainBoard - the main board (motherboard) is an EAX65610904 module, using H5TQ4G63AFR microcircuits, EEPROM: 24C256, SOUND: Audio: NTP7513 and others.
The tuner EBL61400501 TDJM-G101D provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC420DUE-FGA4
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 6 (G to G)
Frequency: 60Hz
Lamp Type: WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
