
PHILIPS
Model: 23PF4321 / 58
Chassis / Version: LC4.1E AB
Panel: T230XW01 V.2
T-CON: V23D C1
Inverter (backlight): CIU11-T0052
MOSFET Inverter: AP4511GH
Power Supply (PSU): PLCD150P1 - 23361 - 3122 133 32992 - P2006016
PWM Power: L6562D (PFC), TEA1601T, TEA1533AT
MainBoard: 3139_123_60192 3139 123 60192 60192 Wk534.3
IC MainBoard: CPU: TDA15021H1 / N1C91; Scaler: GM5221H-LF; NAND Flash: 29LV040CQC-70G; SOUND: TDA1557AW
Tuner: UV1318S / A I H-3
Specifications 23PF4321
PHILIPS 23PF4321
General recommendations for repairing TV LCD
Possible malfunctions
- PHILIPS 23PF4321 does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
With such manifestations, a malfunction is most likely to be detected in the PLCD150P1 power supply module. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of the power switches of the converters and rectifier diodes for the presence of a possible short circuit.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM chips L6562D (PFC), TEA1601T, TEA1533AT are usually checked by replacing with new ones, or obviously working.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
These manifestations can be triggered by the power module, or by inverter defects, as well as by the distortion of the currents in the lamps due to their uneven wear. After checking all the electrolytic capacitors of the filters that are involved in the power supply of the inverter, it is necessary to ring in its converter the power switches for breakdown and the secondary windings of the transformers for an open.
Sometimes, for diagnostic purposes, it is necessary to disable the inverter protection. In such cases, special care must be taken during work, and the protection circuits should be restored immediately after the repair is completed.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the 3139_123_60192 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: TDA15021H1 / N1C91; Scaler: GM5221H-LF; NAND Flash: 29LV040CQC-70G; SOUND: TDA1557AW requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
The malfunction of the UV1318S / A I H-3 tuner is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Entrust repair to professionals with sufficient experience in the field of repair of electronic equipment.
Service manual and schematic diagram --------------------> PHILIPS 23PF4321 Chassis LC4.1E AB.
20PF4321/01, 23PF4321/01, 20PF4321/58, 23PF4321/58, 20PF5321/01, 23PF5321/01, 20PF5321/58, 23PF5321/58, 15PF4121/01, 20PF4121/01, 15PF4121/58, 20PF4121/58, 15PF5121/01, 20PF5121/01, 15PF5121/58, 20PF5121/58


3139_123_60192
3139_123_60192 can be used in TVs:
PHILIPS 20PF4110S/58 (Panel LC201V02 (SD)(B1)), PHILIPS 15PF4121/58 (Panel LC150X02 (TL)(01)), PHILIPS 15PF5120/58 (Panel LC150X02), PHILIPS 15PF5121/58 (Panel IDM69E1S51718 Rev:01 QD15XL16 ), PHILIPS 15PF5121/58 (Panel T150XG01 V.3), PHILIPS 20HF5474/10 (Panel LC201V02 (SD)(D1)), PHILIPS 20PF4121/58 (Panel LC201V02 (SD)(B1)), PHILIPS 20PF5120/58 (Panel A201SN02 V4), PHILIPS 20PF5320/58 (Panel LC200WX1 (SL)(01)), PHILIPS 20PFL4101S/60 (Panel LC201V02 SD B1), PHILIPS 20PFL4102S/60 (Panel LC201V02 (SD)(D1)), PHILIPS 20PFL4102S/60 (Panel LC201V02 (CD)(B1)), PHILIPS 20PFL4112S/60 (Panel LC201V02 (SD)(B1)), PHILIPS 20PFL4112S/60 (Panel LC201V02 SD D1), PHILIPS 20PFL4122/58 (Panel A201SN02 V.5), PHILIPS 20PFL5122/58 (Panel A201SN02 V.5), PHILIPS 23PFL5322/58 (Panel T230XW01 V.3), PHILIPS 23PF4321/58 (Panel T230XW01 V.2).
The appearance of the power supply
Main features of the PHILIPS 23PF4321 device:
Installed matrix (LCD panel) T230XW01 V.2.
The matrix control uses the Timing Controller (T-CON) V23D.
To power the backlight used inverter CIU11-T0052. As power elements of the inverter, switches of the type AP4511GH are used.
The necessary supply voltages for all nodes of the PHILIPS 23PF4321 television are generated by the PLCD150P1 power supply module or its analogs using L6562D (PFC), TEA1601T, TEA1533AT microcircuits.
MainBoard - the main board (motherboard) is a module 3139_123_60192, using CPU chips: TDA15021H1 / N1C91; Scaler: GM5221H-LF; NAND Flash: 29LV040CQC-70G; SOUND: TDA1557AW and others.
The UV1318S / A I H-3 tuner allows you to receive television programs and tune to channels.
Additional technical information about the panel:
Brand: AUO
Model: T230XW01 V2 1 Compatible model
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.0 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 508.152x285.696 mm
Surface: Antiglare (Haze 26%), Hard coating (3H)
Brightness: 500 cd / m²
Contrast Ratio: 450: 1
Display Colors: 16.7M (8-bit)
Response Time: 6/10 (Tr / Td)
Frequency: 60Hz
Lamp Type: 8 pcs CCFL Embedded (Inverter)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V