Technical description and composition of the TCL 39E5000F3D TV, type of panel and applicable modules. The composition of the modules.TCL LED
Model: 39E5000F3D
Chassis / Version: MS82S0
Panel: V390HK1-LS5
T-CON: V236H3-CS3-C
LED driver (backlight): L390H1-1EC
PWM LED driver: ATP360A13, HAI7203HA, HAI5208BP
MOSFET LED driver: M8014D
Power Supply (PSU): PE421C5
PWM Power: FSL206MR, FAN7930C, FSFR1700XS
MOSFET Power: K12A50D
MainBoard: 40-MS82S0-MAD2XG (H)
IC MainBoard: MST6E182VS-LF, 25Q32A-100HIP, 24C64, K4T51163QT-BCF7, IT6633E-P, TPA3110D2
Tuner: F35WT-3-E
Technical Specifications L39E5000F3DE
TCL 39E5000F3D
General repair guidelines for TV LCD LED
Possible malfunctions
- TCL 39E5000F3D does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
Most likely in this case, the main switching power supply (IIPS) PE421C5 is faulty. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, check the serviceability of the power switches (K12A50D) and rectifier diodes for possible breakdown (short circuit).
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback circuits (OOS) of stabilization. PWM controllers (PWM) FSL206MR, FAN7930C, FSFR1700XS, if they do not have visible damage to the case and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, sometimes you can detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the 40-MS82S0-MAD2XG motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements MST6E182VS-LF, 25Q32A-100HIP, 24C64, K4T51163QT-BCF7, IT6633E-P, TPA3110D2. BGA chip malfunctions are usually easy to detect by warming up.
Before changing the F35WT-3-E tuner, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding tuner pins and checked for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
- Owners and users of the TCL 39E5000F3D TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> EEPROM + T-CON TCL 39E5000F3D, Main: 40-MS82S0-MAD2XG (H), Panel: V390HK1-LS5
To reduce the backlight current in LED drivers with the HAI7203HA controller, the total resistance of the resistors from terminal 12 (ISET) to the housing should be increased. Currents will proportionally decrease in each of the 8 channels. With a parallel connection of channels, currents are summed.
The appearance of the MainBoard 40-MS82S0-MAD2XG is shown in the figure below:40-MS82S0-MAD2XG
40-MS82S0-MAD2XG can be used in TVs:
ERISSON 23LET70 (Panel LTA230AP01), GOLDSTAR 32A340R (Panel LVW320SSTM E1), GoldStar LT-42A320F (Panel LVF420AUBK), MYSTERY MTV-3225LW (Panel LVM320CSTME13V4), MYSTERY MTV-4019LW (Panel LVF390CMTM E13 V5), MYSTERY MTV-3219LW (Panel LVW320CSTME18 V2), TCL 40D3200 (Panel LTA400HM13 ), TCL 39D3320 39D3320F (Panel LVF390CMTM E13 V2), TCL 39E5000F3D (Panel V390HK1-LS5), THOMSON T39ED33HU (Panel LVF390CMTME15V2), THOMSON T32ED33U (Panel LSC320AN01-C06), THOMSON T32E32U (Panel LVW320SSTT E1).
The appearance of the power supply
Key Features of the TCL 39E5000F3D:
Installed matrix (LED-panel) V390HK1-LS5.
The matrix control uses the Timing Controller (T-CON) V236H3-CS3-C.
The LED driver L390H1-1EC is used to power the backlight LEDs, it is controlled by the ATP360A13, HAI7203HA, HAI5208BP PWM controller. As the power elements of the LED driver, keys of the type M8014D are used.
The necessary supply voltages for all nodes of the TCL 39E5000F3D TV are generated by the PE421C5 power module or its analogs using FSL206MR, FAN7930C, FSFR1700XS microchips and K12A50D type power switches.
MainBoard - the main board (motherboard) is a 40-MS82S0-MAD2XG module, using microcircuits MST6E182VS-LF, 25Q32A-100HIP, 24С64, K4T51163QT-BCF7, IT6633E-P, TPA3110D2 and others.
The F35WT-3-E tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V390HK1-LS5
Type: a-Si TFT-LCD, Panel
Diagonal size: 39 inch
Resolution: 1920x1080, FHD
Display Mode: MVA, Normally Black, Transmissive
Active Area: 853.92x480.33 mm
Surface: Antiglare (Haze 3.5%), Hard coating (3H)
Brightness: 350 cd / m²
Contrast Ratio: 5000: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 8.5 (G to G)
Frequency: 120Hz (60Hz Input)
Lamp Type: WLED Embedded (LED Driver)
Signal Interface: LVDS (2 ch, 8-bit), 61 pins
Voltage: 12.0V
TCL L39E5000F3DE TV with a 39 "(99 cm) diagonal LCD display in 16: 9 format. The brightness of the screen declared by the manufacturer is 350 cd / m² by LED backlighting. Dynamic contrast ratio of 30,000: 1 is achieved by special control of the LEDs depending on In the LCD panel of this TV, end LED backlighting is implemented - Edge LED.
There is support for 3D images with active (shutter) technology for separating the right and left channels. The design and technical capabilities of the TV include watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD).
The L39E5000F3DE is equipped with SMART software, embedded applications and the ability to work on the Internet. Connecting to the Internet can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x4, USB x2, Wi-Fi. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
The digital tuner is capable of receiving television channels in DVB-T MPEG4 standards.
The power consumed by the TV in operating mode from the network is 75 watts.
Overall dimensions: with stand 891x589x231 mm, without stand 891x534x71 mm.
TV Weight: with stand: 14.2 kg, without stand: 11.9 kg.
Attention! The panel of the TCL L39E5000F3DE LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
