REPAIRING AND NOT THROWING AWAY

Richtige Fernseher haben Röhren!

Richtige Fernseher haben Röhren!

In Brief: On this site you will find pictures and technical information about Service Modes, Circuit Diagrams, Firmware Update procedure, Disassemble procedure, Universal remote control set-up codes, Troubleshooting and more....

If you go into the profession, you will obtain or have access to a variety of tech tips databases HERE IT IS Master Electronics Repair !.

These are an excellent investment where the saying: 'time-is-money' rules. However, to learn, you need to develop a general troubleshooting approach - a logical, methodical, method of narrowing down the problem. A tech tip database might suggest: 'Replace C536' for a particular symptom. This is good advice for a specific problem on one model. However, what you really want to understand is why C536 was the cause and how to pinpoint the culprit in general even if you don't have a service manual or schematic and your tech tip database doesn't have an entry for your sick TV or VCR.

While schematics are nice, you won't always have them or be able to justify the purchase for a one-of repair. Therefore, in many cases, some reverse engineering will be necessary. The time will be well spent since even if you don't see another instance of the same model in your entire lifetime, you will have learned something in the process that can be applied to other equipment problems.
As always, when you get stuck, checking out a tech-tips database may quickly identify your problem and solution.In that case, you can greatly simplify your troubleshooting or at least confirm a diagnosis before ordering parts.

Happy repairing!
Today, the West is headed for the abyss. For the ultimate fate of our disposable society is for that society itself to be disposed of. And this will happen sooner, rather than later.

How to use the site:

- If you landed here via any Search Engine, you will get what you searched for and you can search more using the search this blog feature provided by Google. You can visit more posts scrolling the left blog archive of all posts of the month/year,
or you can click on the main photo-page to start from the main page. Doing so it starts from the most recent post to the older post simple clicking on the Older Post button on the bottom of each page after reading , post after post.

You can even visit all posts, time to time, when reaching the bottom end of each page and click on the Older Post button.

- If you arrived here at the main page via bookmark you can visit all the site scrolling the left blog archive of all posts of the month/year pointing were you want , or more simple You can even visit all blog posts, from newer to older, clicking at the end of each bottom page on the Older Post button.
So you can see all the blog/site content surfing all pages in it.

- The search this blog feature provided by Google is a real search engine. If you're pointing particular things it will search IT for you; or you can place a brand name in the search query at your choice and visit all results page by page. It's useful since the content of the site is very large.

Note that if you don't find what you searched for, try it after a period of time; the site is a never ending job !

..............The bitterness of poor quality is remembered long after the sweetness of todays funny gadgets low price has faded from memory........ . . . . . .....
Don't forget the past, the end of the world is upon us! Pretty soon it will all turn to dust!

©2010, 2011, 2012, 2013, 2014 Frank Sharp - You do not have permission to copy photos and words from this blog, and any content may be never used it for auctions or commercial purposes, however feel free to post anything you see here with a courtesy link back, btw a link to the original post here , is mandatory.
All posts are presented here for informative, historical and educative purposes as applicable within fair use. NOTHING HERE IS FOR SALE !

Sunday, 14 June 2020

BENQ 2450HM MONITOR HOW TO ENTER THE SERVICE MODE HOW TO UPDATE THE FIRMWARE, POWER BOARD - SMPS - SCHEMATIC AND GENERAL TROUBLESHOOTING

BenQ G2450HM, GL2450HM, GL2450HE MONITOR how to update the firmware, SMPS schematic, troubleshooting, Service mode
How to enter the service mode
Connect signal source and power cable to monitor and DC off it.
Press “menu” key and “power on” key synchronously as below figure. When the screen lights, release the two buttons and then press “menu” again to open below factory menu.
If a bad smell or an abnormal sound appears to come from the monitor, contact your nearest BenQ service center for assistance immediately.
Be careful do not touch the rear side directly because of the backlight high voltage.
F/W Upgrade SOP: Upgrade by 715GT089-B/ C
Materials list
Connection
Install the USB driver
When insert the USB cable to PC USB port, will pop up a Hardware Wizard to help you install the USB driver if you use this ISP board first time. You can install it successfully as the below instruction step by step.
Remark: The USB driver files path: D:\FTC100103(Mstar)\FTCUSB.INF

Install the ISP tool.:  Copy the three files in one folder. And then double click ISP tool.exe
Set the parameters in “Device” window. Tick “WP Pin pull to high during ISP”.
Connect to the monitor. Click “Connect”. If the tool communicate with monitor successfully, the tool will detect the flash type of monitor.
Load the F/W you want to upgrade.
Set the restore address.:  fill “0x03F000” and “4KB” as follow.
Set parameter in “Auto” window. If you have set “Restore address”, please tick “Restore Data”.
Processing of upgrade. After clicking “Run”, the tool start to program. It is forbided to power off monitor or switch off connection during programming.
Successful upgrade. When upgrade successful, there will be green Pass letter appearing.
Check the FW version after upgrade.( Take below figure as an instance)
(1)Connect signal source and power cable to monitor and DC off it.
(2) Press “menu” key and “power on” key synchronously as below figure. When the screen lights, release the two buttons and then press “menu” again to open below factory menu.
If the version is right, please do factory reset in user menu as below, or re-upgrade F/W as the above steps.
The reset will turn off burn in mode.
Troubleshooting.Can’t Entry ISP Mode?  Click “Config” to check the port type is USB. If no selection of USB as below please disconnect the JIG and then link it again.
Check the cables and ISP JIG are connected fluently.
Click the “Dis Con” and click “Connect” again.
AC off the monitor for a while and retry it.
Change advanced ISP tool.
Change ISP JIG or cable.
Change PC.
Power Board Schematics: GL2450HM//GL2450HE 715G5000P01000003H and G2450HM 715G5000P01001003H
GL2450HM//GL2450HE 715G5000P01000003H SMPS schematic
G2450HM 715G5000P01001003H: SMPS schematic
Troubleshooting
The image is blurredR
Readthe instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
How do you use a VGA extension cable
Remove the extension cable for the test. Is the image now in focus? If not, optimize the image by working through the instructions in the "Adjusting the refresh rate" section on the link "Adjusting the Screen Resolution". It is normal for blurring to occur due to conduction losses in extension cables. You can minimize
these losses by using an extension cable with better conduction quality or with a built-in booster.
The blurring only occur at resolutions lower than the native (maximum) resolution.
Read the instructions on the link "Adjusting the Screen Resolution" on the CD. Select the native resolution.
Pixel errors can be seen
One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color.
Clean the LCD screen.
Cycle power on-off.
These pixels are permanently on or off and that is a natural defect occurs in LCD technology.
The image has a faulty coloration
It has a yellow, blue or pink appearance.
Select MENU > PICTURE > Color > Reset Color, and then choose “YES” in the “Caution” message box to reset the color settings to the factory defaults.
If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, contact your dealer to get necessary support.
No image can be seen
Is the prompt on the display illuminated in green?
If the LED is illuminated in green and there is a message “Out of Range” on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one of the supported mode. Please read the “Preset display modes” section from the link "Adjusting the Screen Resolution".
Faint shadow from the static image displayed is visible on the screen
Activate the power management function to let your computer and monitor go into a low power "sleep" mode when not actively in use.
Use a screensaver to prevent the occurrence of image retention.
The prompt on the display illuminated in orange
If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
The prompt on the display not illuminated at all
Check the power supply mains socket, the external power supply and the mains switch.
The image is distorted, flashes or flickers
Read the instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
Running the monitor at its native resolution, but the image is still distorted
Images from different input sources may appear distorted or stretched on the monitor running at its native resolution. To have the optimal display performance of each type of input sources, you can use the "Display Mode" function to set a proper aspect ratio for the input sources.
The image is displaced in one direction
Read the instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
OSD controls are inaccessible
To unlock the OSD controls when the OSD is preset to be locked, press and hold the “MENU” key for 15 seconds to enter the “OSD Lock” option and make changes.
Alternatively, you may use < or >  keys to select “NO” in the “OSD Lock” submenu from the “OSD Settings” menu (under SYSTEM), and all OSD controls will be accessible.