Technical description and composition of the FUSION FLTV-24T22 TV, type of panel and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-24T22
Chassis / Version: V1M12
Panel: M236HGE-P02
MainBoard: CV9202L-T
IC MainBoard: CPU: SPV9202BD; SPI Flash: W25Q64FVSIG; SOUND: YD1517P
Tuner: ST03WS-2A-E
Technical Specifications FLTV-24T22
FUSION FLTV-24T22
General repair guidelines for TV LCD LED
Repair of the FUSION TV with the V1M12 chassis should begin with a careful external inspection of all its components and modules. It often happens that visible damage to elements or connections helps determine the direction of the troubleshooting. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
In the absence of any signs of operability, when the FUSION FLTV-24T22 does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the TV power module. With the same manifestations, the power regulator of the control processor on the motherboard may be faulty. In the absence of swollen filter capacitors of the secondary rectifiers, the diagnostics of the power supply should be started by checking the fuse and, if it is broken, it is first necessary to check all the power semiconductor elements of the primary circuit - diodes and transistors for the possibility of an avalanche or thermal breakdown.
The reasons for the breakdown of the power switch in pulsed power supplies (IIPS) can be different, for example, a malfunction of semiconductor elements or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or broken resistors in its bundle.
If the FUSION FLTV-24T22 does not have an image, there is sound and the channels are switched, there is a possibility of a malfunction of the display backlight, or their power converter - LED driver. Sometimes when you turn on the image appears and disappears immediately. In such cases, it is necessary to check the electrolytic capacitors of the power filter of the LED driver itself, including in the secondary rectifier of the main PSU. It should be remembered that when disabling protection in order to diagnose a malfunction, there is always a risk of failure of the power elements of the LED driver. After repair, it is imperative to restore all standard converter protection circuits.
Diagnosis and repair of the CV9202L-T motherboard is carried out by checking the performance of the stabilizers or power converters of the module chips. In some cases, a software update is required. Board repair and replacement of FLASH W25Q64FV microcircuits are carried out in the presence of the necessary equipment, and the corresponding element base. Faults associated with the use of BGA processor soldering technologies can be localized by the heating method.
Owners of the FLTV-24T22 TV are advised to contact qualified personnel with experience only for repair! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> CV9202L-T
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-24T22 V1M12, Main: CV9202L-T, Panel: M236HGE-P02
In case of failures in Winbond's SPI FLASH software, sometimes they can temporarily restore their performance after temperature exposure, for example, heating with a soldering station or a lighter. Often this is enough to be able to read the regular software content. After that, the chip should be replaced with a new one.
Repair MainBoardThe appearance of the MainBoard CV9202L-T is shown in the figure below:
CV9202L-T
The MainBoard CV9202L-T uses the SPV9202BD processor, W6310GKB-12 RAM, and SPI FLASH 8Mb ROM.
It is advisable to start repairing the motherboard by checking all voltage converters and linear stabilizers necessary to provide power to the nodes and chips in the operating and standby modes. The processor core is powered by + 1V. Also, for operation of the SPV9202BD, + 2.5V and + 3.3V voltages are required. Check the power of the LCD panel (depending on the type, + 5V or + 12V), it is convenient to measure directly on the LVDS connector. If, in the presence of the necessary supply voltage, the TV does not exit Stand-by mode, does not respond to the Remote Control and control buttons, the SPI Flash 25Q64 firmware should be updated.
CV9202L-T can be used in TVs:
AIWA 24LE7020 (Panel V236BJ1-P01), BBK 22LEM-1006/FT2C (Panel M215HTN01.1 KM215N19-AU-01), DEXP 19A3100 (Panel CX185LEDM), DEXP 22A7100 (Panel T215HVN01.0 M215HVN01.0), FUSION FLTV-24T22 (Panel M236HGE-P02), FUSION FLTV-22T22 (Panel 720p HD 1366x768), SHIVAKI STV-24LED14 (Panel V236BJ1-P01 / CX236LEDM), SUPRA STV-LC24T410FL (Panel M236HGE-P01), SUPRA STV-LC19T410WL (Panel HK185WLEDM CH25H), SUPRA STV-LC22T410FL (Panel LC215DT5A), SUPRA STV-LC24T410WL (Panel HK236WLEDM-CH24H), SUPRA STV-LC19T880WL (Panel LC185TT7A).
Main features of the FUSION FLTV-24T22 device:
Installed matrix (LED-panel) M236HGE-P02.
The required supply voltage for all nodes of the TV FUSION FLTV-24T22 provides a switching power supply.
MainBoard - the main board (motherboard) is a CV9202L-T module, using Cpu chips: SPV9202BD; SPI Flash: W25Q64FVSIG; SOUND: YD1517P and others.
The ST03WS-2A-E tuner provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: M236HGE-P02
Type: a-Si TFT-LCD, CELL
Diagonal size: 23.6 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 521.28x293.22 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 6.3% (with Polarizer)
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit)
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
FUSION FLTV-24T22 TV with M236HGE-P02 LCD display, 24 "(61 cm) diagonal size in 16: 9 format. The required brightness of the screen is 280 cd / m² by LED backlighting. Dynamic contrast ratio of 80000: 1 is achieved by special control of the LEDs The LED-panel of this TV is equipped with LED end-lighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM , NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, MPEG4, MKV, JPEG. Stereo sound is realized by two built-in speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
A digital tuner is capable of receiving television channels in the DVB-T, DVB-C, DVB-T2 standards.
Attention! The panel of the M236HGE-P02 FUSION FLTV-24T22 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.
